THOMSON 00132494, Руководство по эксплуатации

Страница: 5 / 62

3
5.1. Bluetooth
®
pairing
Note – Pairing
• Make sure that your Bluetooth
®
-capable terminal device is on
and Bluetooth ® is activated.
• Make sure that your Bluetooth
®
-capable terminal device is
visible for other Bluetooth
®
devices.
• For more information, please refer to the operating
instructions of your terminal device.
• The earphones and the terminal device should be no further than
one metre apart. The smaller the distance, the better.
• Switch on the earphones with the MF button (5).
• Press and hold the MF button (5) until the red and blue LEDs
flash alternatingly. The earphones are searching for a Bluetooth
®
connection.
• Open the Bluetooth
®
settings on your terminal device and wait
until Thomson WEAR6309 appears in the list of Bluetooth
®
devices found.
• Select Thomson WEAR6309 and wait until the earphones are
listed as connected in the Bluetooth ® settings on your terminal
device.
Note – Bluetooth ® password
Some terminal devices require a password in order to connect to
another Bluetooth
®
device.
• If your terminal device requests a password for connection to
the earphones, enter 0000 .
Note
• Once the connection has been established, a voice says,
“Connected” .
• If the connection attempt takes longer than 300 seconds to
complete, it is cancelled and the LEDs go out.
• In this case, repeat the steps listed previously under 5.1
Bluetooth ® pairing.
5.2. Automatic Bluetooth
®
connection (after successful
pairing)
Note
• Make sure that your Bluetooth ® -capable terminal device is on
and Bluetooth ® is activated.
• Make sure that your Bluetooth ® -capable terminal device is
visible for other Bluetooth ® devices.
• For more information, please refer to the operating
instructions of your terminal device.
• Switch on the earphones with the MF button (5). The blue LED
begins to flash and the earphones automatically connect with
the last terminal device used.
Note
• Once the connection has been established, a voice says,
“Connected” .
Note
• If the connection attempt takes longer than 300 seconds to
complete, it is cancelled and the LEDs go out. In this case,
repeat the steps listed previously under 5.2.
• It may be necessary to change the settings on your terminal
device to enable it to automatically connect to the earphones.
Note – Connection impaired
After the headset and terminal device have been paired, a
connection is established automatically. If the Bluetooth ®
connection is not established automatically, check the following:
• Check the Bluetooth ® settings of your terminal device to see
whether Thomson WEAR6309 is connected. If not, repeat the
steps listed under 5.1. Bluetooth
®
pairing .
• Check whether obstacles are impairing the range. If so, move
the devices closer together.
• The performance can also be affected by a weak battery.
5.3. Bluetooth
®
multipoint connection
These earphones can connect to two Bluetooth
®
-enabled terminal
devices simultaneously (multipoint).
• First connect the earphones with the first terminal device as
described in 5.1.
• Then disable Bluetooth ® on that terminal device.
• Next, connect the earphones with the second terminal device
as described in 5.1.
• Activate Bluetooth
®
on the first terminal device once more. The
earphones now connect to that terminal device automatically.
5.4. Audio playback
Note
• Note that the functions described under 5.3 . and 5.4 . are
only possible with an active Bluetooth
®
connection.
• Your terminal device must also support the individual
functions.
• For more information, please refer to the operating
instructions of your terminal device.
• Functions can still be controlled directly via the terminal device.
• Set the volume on your terminal device to a low level.
• Switch on the earphones with the MF button (5). Upon
successful connection, a voice says, “ Connected ”.
• Start audio playback on the connected terminal device.
• Press (4) to increase the volume. There is an
announcement when the maximum volume is reached.
• Press Volume - (6) to reduce the volume.
• Press the MF button (5) to start or pause audio playback.
• Press and hold Jump forward one titl e (4) to skip to the
next title.
• Press and hold Jump backward one title (6) to skip to the
previous title.