THK TJU Скачать руководство пользователя страница 27

Страница: 27 / 134

2. Installation

How to install

2-12

TNU

2-2-1

Standards for installation

When installing the TNU and TJU to the control panel, observe the following installation standards:

⿟

Install TNU and TJU onto the wall perpendicularly so that the fronts directly face to the opera-
tor.

⿟

The space between TNU and TJU must be 10 mm or more.

⿟

To allow for cooling by fan or natural convection, the space between TNU/TJU and right/left wall
must be 30 mm or more.

⿟

To allow for cooling by fan or natural convection, the space above/below TNU or TJU must be
50 mm or more.

⿟

If the temperature in the control panel exceeds 40°C, install cooling fan(s).

50 mm or
more

Control panel

10 mm or
more

30 mm or more

50 mm or
more

30 mm or more

10 mm or
more

TNU

TJU

Driver controller

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Содержание TJU







































































































































Результаты поиска

Содержание TJU

Отзывы:

Бренды по названию

Популярные бренды

THK TJU, Инструкция по эксплуатации

Результаты поиска

Содержание TJU

Отзывы:

Бренды по названию

Популярные бренды