manualshive.com logo in svg

THK TJU, Инструкция по эксплуатации

Поделиться
Скачать
THK TJU Скачать руководство пользователя страница 21

2. Installation

1. 

Check products

2-6

TNU

(1) Power-on display (red)

When this light is on, the power supply 24 V DC is being input.

(2) Upper-level network communication status display (green)

When this light is on, it indicates communication in process with 

the upper-level master device. Light goes off at a TNU network 

setting error, indicating a failure of communication with the master. 

The light remains off until alarm reset processing is done.

(3) TACnet communication status display (green)

When this light is on, it indicates no communication with lower-

level devices, or normal communication. When the number of 

retries has been surpassed and a communication error occurs, 

the light goes off and remains off until alarm reset processing is 

done.

(4) Error display (red)

When normally connected with the upper-level master device, 

the light goes off. When this display is flashing, it is in startup or a 

TNU system error has occurred.

CN1

 Upper-level network communication connector

Connect to the upper-level device network.

LED (LINK)

Indicates communication status with EtherNet/IP network.

Mode change switch

Switch to select the upper-level device that transmits command 

to the lower-level device

On CN1 side, the communication command by the upper-level 

network master (I/O mode)

On CN2 side, the communication command by the upper-level 

device supporting TACnet (PC/TDO mode)

CN2

Communication connector

Connector to connect the PC or TDO.

CN3

Communication connector

Connector to connect to the TJU.

LED (MS)

Indicates unit operation status.

LED (NS)

Indicates network communication status.

CN4

Power connector

Connector for the input power supply.

(1) (2) (3) (4)

MS/NS LED display

LINK

Link

Lit off

No link, no data communication

Green lit

Link established

Green flashing

In data communication

MS

Module status

Lit off

Power OFF

Green lit

In normal operation

Green flashing

Unit setting not done

Red lit

Fatal unit error

Red flashing

Clearable unit error

NS

Network status

Lit off

Power OFF / IP address unset

Green lit

Online: connection established

Green flashing

Online: connection unestablished

Red lit

IP address overlap (fatal error)

Red flashing

Communication time out

TNU-EP

(FG)

Ground wire is connected.

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Содержание TJU







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды