THK TJU Скачать руководство пользователя страница 112

Страница: 112 / 134

8. Troubleshooting

8-3

TNU

Causes and counter measures of alarms

2-1

Causes and counter measures of alarms

No. Alarm name

Generation

status

Causes

Counter measures

1 Net device list

collapse

While energizing Data in TNU flash rom were

corrupted

Replace TNU with new one

Device error While energizing TNU is out of order

Replace TNU with new one

Rotary SW

setup error

While energizing After the start-up, the rotary

SW value was changed

Restore the rotary SW value

to a normal state and turn on

the power again

Upper-level

communication

error

communication

Inconsistency between

master and TNU external

network parameter settings.

Match parameter settings.

Cables between TNU and

master are disconnected or

misconnected.

Replace the cables or

connect them correctly.

TACnet

communication

error

(Lower-level

communication

error)

communication

The CRC error was detected

in the returned data

Eliminate the noise source

from the set environment

Communication data was

corrupted due to noise

Eliminate the noise source

from the set environment

Cable is not properly

connected

Connect the cable in proper

way

Cable is disconnected

Replace the cable with new

one

Connector is not properly

connected

Connect it in proper way

The driver controller is broken Replace the driver controller

with new one

The driver controller is not

power-up

Check if the power of the

driver controller is turned on

There is some driver

controller of the duplicate ID

over the network

Change to a non-duplicate

ID and turn on the power of

the driver controller and TNU

again.

No driver controller is

connected to the ID set for

the net device list.

Set the net device list in

proper way.

Or connect the driver

controller.

The communication speed

with the driver controller is

not aligned

Set the communication

speed in proper way

TJU's termination resistance

setting is wrong

Set the termination resistance

in proper way

* On the D-STEP screen, CC-Link, EtherCAT, EtherNet/IP or DeviceNet communication error and

TACnet communication error are indicated as, respectively, upper-level communication error and

lower-level communication error.

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Содержание TJU







































































































































Результаты поиска

Содержание TJU

Отзывы:

Бренды по названию

Популярные бренды

THK TJU, Инструкция по эксплуатации

Результаты поиска

Содержание TJU

Отзывы:

Бренды по названию

Популярные бренды