Thiele 00900383 Скачать руководство пользователя страница 88

Страница: 88 / 92

eliant

3700 M

anual

4. Verify the sheet sensor’s power-on green LED is illuminated. Is the green LED

illuminated?

a. Yes: Go to step 5.

b. No: Go to step 7.

5. Verify the sheet sensor’s yellow LED sensing indicator illuminates when the sen-

sor is covered, and goes dark when the sensor is uncovered. Is the yellow LED

illuminated when the sheet sensor is covered, and dark when the sensor is uncov-

ered?

a. Yes: Go to step 6.

b No: Go to step 7.

6. Cover the sensor so that the yellow sensing LED is illuminated and press the

reset switch. Did the feeder reset?

a. Yes: The feeder times-out as it should. Go through feeder setup and make

sure the sensor sees the leading edge of the next sheet shortly after a piece

of sheet material is removed from the feeder. If the leading edge of the next

piece of material is not detected in time, the feeder “times-out” and stops,

causing the steady audible beep and reset button lamp to illuminate.

b. No: Go to step 7.

7. Remove the sheet detect sensor harness from CPU connector J6 and measure

for the presence of 12VDC across pins 1 and 3 of connector J6 on the board. Is

the voltage present?

a. Yes: Go to step 8.

b. No: Go to step 9.

8. Test sheet sensor input. Using a small metal blade screwdriver, short pins 1 and

2 together on CPU board connector J6, keep them shorted, and press the reset

button. Does the feeder reset?

a. Yes: The sheet sensor input on the CPU board is good. Repair faulty sheet

sensor harness and/or replace sheet sensor.

b. No: Go to step 9.

9. Replace Reliant Control Assembly.

10. Replace ROM chip

Steady beep is heard, reset

button is illuminated, and

pressing button does not

reset fault (continued)

The following steps assume

the output of the DC power

supply is working and both

5 and 12 volts are present

at the CPU and Expansion

Board input connectors. If

not, see section titled “Fan

does not operate/Testing DC

power supply.”

The following steps assume

the blinking green “heartbeat”

LED is present on the CPU

board. If not, see section

titled “CPU board ‘heartbeat’

pulse not present”.

Problem

Solution

Содержание 00900383





























































































Результаты поиска

Содержание 00900383

Отзывы:

Бренды по названию

Популярные бренды

Thiele 00900383, Руководство пользователя

Результаты поиска

Содержание 00900383

Отзывы:

Бренды по названию

Популярные бренды