Thetford N614E.3F Скачать руководство пользователя страница 9

Installation / Owner’s Manual  9

-  Make sure that the vertical top edge of the baffle is between 6mm [213] below the condenser  and 38mm above the 

bottom of the condenser.

-  Make sure that there is 6mm or less clearance [15] between the rear of the condenser and the baffle.

The doors are made to accept decorative panels.  The decorative panels must be 5mm or less in thickness.  Install the 

decorative door panels in the refrigerator doors before installing the refrigerator in the vehicle.

-  Make an upper door panel that is 548mm wide x 369mm high.

-  Make a lower door panel that is 548mm wide x 803mm high.

-  Pull the panel retainer [37] off each door (See Art00965).

-  Push the decorative door panel [38] into the slots of the door [39].

-  Push each panel retainer into the slot on the edge of the door.

Install Decorative Door Panels

Art00965

37

38

39

Put  the refrigerator in position (See Art02445, Art02442, and Art02272):

Make sure the combustion seal [29] is not broken, is completely 

around the refrigerator mounting flanges, and is between the 

mounting flanges and the wall of the enclosure  If the seal is not 

complete, exhaust fumes can be present in the living area of the 

vehicle.  The breathing of exhaust fumes can cause dizziness, nausea, 

or in extreme cases, death.

-  Push the refrigerator completely into the enclosure. 

-  Put two screws [41] through the upper mounting flange on the front of the refrigerator and 

into the enclosure wall.

-  Put two screws [41] through the lower mounting flange [211] on the front of the refrigerator 

and into the enclosure floor.

Do not omit the bottom trim piece.  This piece is part of the 

combustion seal.

-  Push the bottom trim piece [28] onto the front of the refrigerator.

-  Put two screws [41] through the bottom trim piece, the mounting flange, and into the 

floor.

-  Put two screws through mounting flange on the rear of the refrigerator and into the 

floor. 

Install the Refrigerator

Art02272

41

28

41

211

NOTICE

WARNING

!

WARNING

!

Art02445

40

29

28

41

Содержание N614E.3F

















Отзывы: