Thetford N614E.3F Скачать руководство пользователя страница 12

Installation / Owner’s Manual  12

3.  Change the position of the door handles (See Art01727):

-  Remove the screws [41] and door handle [70] from each door.

-  Reverse each door handle and put the lower door handle on the upper door and the 

upper door handle on the lower door.

-  Attach each door handle with the screws.

4.  Reinstall the doors (See Art02273):

Turn the doors180° from their original position.

-  Turn each of the lower hinge pins [64] into the lower cabinet hinges.

To prevent damage to the threads of the hinge pins, turn the hinge pins by 

hand until tight and then tighten with a screwdriver.

Apply Loctite removable thread locker (blue) to the threads of 

the hinge screws before assembly to prevent loosening during 

use.  Do not allow Loctite to contact any of the plastic surfaces 

of the refrigerator because it can damage those surfaces.

-

  Put the washer onto the lower hinge pin of the lower door only

-  Put the LH lower hinge support [256] onto the lower hinge of the lower door only.

-  Put each door down onto the lower hinge pin.

-  Align the holes in the upper hinges and hold in this position.

-  Turn the upper hinge pin into the hinges of each door.

-  Tighten the hinge pins.

-  Put the storage bins in the doors.

NOTICE

CAUTION

!

63

66

254

64

67

256

Art02273

NOTICE

41

70

Art01727

Содержание N614E.3F

















Отзывы: