background image

9

40.021.119 - rev. 00 - 2019

English

IMAC 4000 GAS US

5  

MAINTENANCE

5.1  

Maintenance table

Use the table in this booklet to record performed

maintenance after each winter season.

5.2  

General

Use the table in this booklet to record performed

maintenance after each winter season.

When the convector heater is to be stored for a

longer period of time:

1.  Switch on the convector heater for three

     minutes. This will protect the fuel pump

     against corrosion.

2.  Make sure the burner head is free from dust

     and deposit.

     A dirty heater head will cause insufficient

     combustion, resulting in the development of

     soot and carbon monoxide and causing

     damage to the burner room.

3.  Close the valve of the fuel supply.

4. Disconnect the power plug.

 

Warning

 

Switch off power during maintenance!

 Hot

 

Do not touch the flue and air outlet!

 

Wait until the flue and the air outlet have

 

cooled down sufficiently before carrying

 

out any maintenance.

5.3  

V-belts (Fig. 7 )

Impression

V-belt tension

13 mm

32,2 N

1. Remove the upper and lower side panels (A).

2. Lower the motor (B) by turning the adjusting

nuts (C).

3. Remove the old V-belts (D).

Install new V-belts in reverse order.

 

Caution

 

Tension the V-belts according to the

 table.

Description yearly check.

Who

Check the general condition of the fans, ignition electrode, ionization probe, burner,

electrical installation, combustion room, and heat exchanger.

Dealer

Check the fuel lines for dirt and leakage.

User

Check the air inlet for dirt

User

Check the fan of the burner for corrosion and dirt.

User

Check the fan for corrosion and dirt.

User

Check the fan motor for proper operation

User

Check the ionization probe for signs of damage. Make sure the ionization probe is free

from dust and deposit.

User

Check the settings of the ignition electrode.

Dealer

Check the distributor head for dust, etc.

Dealer

Clean the heat exchanger.

Dealer

Clean the inlet/outlet.

User

Check the V-belts.

User

Check the torque of the armatures. The torque value should be 60 Nm.

User

Содержание IMAC 4000 GAS US





















Отзывы: