Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 27 / 442

background image

Preface

Contacting Us

Thermo Scientific

ISQ 7000 Hardware Manual

xxvii

Biological Hazard Warning Note

In laboratories where samples with potential biological hazards are handled, the user must
label any equipment or parts which might become contaminated with biohazardous material.

The appropriate warning labels are included with the shipment of the instrument. It is the
user’s responsibility to label the relevant parts of the equipment.

When working with biohazardous materials, you are responsible for fulfilling the following
mandatory requirements:

• Providing instructions on how to safely handle biohazardous material.

• Training operators to be aware of potential hazards.

• Providing personal protective equipment.

• Providing instructions for what to do if operators are exposed to aerosols or vapors during

normal operation (within the intended use of the equipment) or in case of single fault
situations such as a broken vial. The protective measures must consider potential contact
with the skin, mouth, nose (respiratory organs), and eyes.

• Providing instructions for decontamination and safe disposal of relevant parts.

Venting Toxic Gases

When analyzing toxic compounds, be aware that during the normal operation of the GC
some of the sample might be vented outside the instrument through the split and purge flow
vents; therefore, be sure to vent the exhaust gases to a fume hood. Consult local
environmental and safety regulations for instructions in exhausting fumes from your system.

Contacting Us

There are several ways to contact Thermo Fisher Scientific for the information you need.

WARNING

The user or operator is responsible for the safe handling of hazardous

chemicals or biological compounds including (but not limited to) bacterial or viral
samples and the associated waste, according to international and local regulations.

AVERTISSEMENT

L’utilisateur ou l’opérateur est responsable de la manipulation sûre des

composés chimiques et biologiques dangereux, y compris, sans s’y limiter, les échantillons
bactériens ou viraux et les déchets associés, conformément aux réglementations
internationales et locales.

«
...
25
26
27
28
29
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 16

Бренд: DayTronic Страницы: 54

Бренд: Bacharach Страницы: 2

Бренд: Bachmann Страницы: 33

Бренд: OHAUS Страницы: 84

Бренд: KROHNE Страницы: 34

Бренд: Keithley Страницы: 44

Бренд: Keithley Страницы: 76

Бренд: Keithley Страницы: 12

Бренд: Keithley Страницы: 281

Бренд: A&D Страницы: 39

Electone Stagea ELS-01C

Бренд: Yamaha Страницы: 248

Бренд: Hama Страницы: 16

FLEXFLO M4 Series

Бренд: Blue-White Страницы: 64

Бренд: Ecolab Страницы: 95

Бренд: janitza Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды