background image

MAX/Wall

®

Technical Wall System

51

of Cabinet

C

L

Section 4 – Installing Supporting Furniture and Casework

Figure 4-23 Adjusting Glass Sliding Doors

4.10 Floor and Wall-Mounted

Cabinets 

(cont.)

Adjusting Glass Doors
Refer to Figure 4-23.

1.  When adjusting glass doors, do not over-tighten

screws.

1/32" (.031")

Clearance

Rear T

rack

Top of Unit

Front T

rack

3.00"

3.00"

Caution: Installer must

adjust these screws to

within 1/32" of top of

glass at installation

Installing Upper Storage Cabinets
Refer to Figure 4-24:
Warning: Read these instructions carefully.

Improperly installed cabinets can detach from the

wall, fall, and cause serious injury.

1. Determine where the top of the cabinet will be

located and use a carpenter’s level to draw a 

horizontal line 4-3/4" below this height.

2. Locate the bottom edge of the steel cleat provided

with the cabinet on this line and mount cleat on

wall using an appropriate fastener. The steel cleat

does not have pre-drilled holes. Hole size and

location is determined at the job site. 

Note:

If the

wall is not true, it will be necessary to shim behind

the cleat.

3. To mount the lower cleat, measure the distance

between the hanger channels on the cabinet and

add 2-1/4". Using this figure, measure down from

the top of the existing cleat and mark a point. Use

a carpenter’s level to draw a horizontal line at this

point. Repeat Step 2 to install the cleat.

4. Hang cabinet on the cleats.

5. Place an additional screw through the cabinet near

the bottom into a stud to prevent accidental dis-

lodging from the wall cleat. If a stud cannot be

located, use appropriate fasteners for a hollow

wall as noted below. 

Note:

A wood filler (not 

supplied) should be placed between back of the

cabinet and wall.

Wall Conditions

6. These cabinets are hung on steel wall cleats. The

cleats are furnished, but not the fasteners for

attaching the cleat to the wall. The fasteners are

standard hardware items which can be obtained

locally to suit one of the following wall conditions:

7. 

Studded Walls -

(Wood or aluminum) Use round

head sheet metal screws of adequate size and

length, make sure the screws are driven into the

studs.

8. 

Hollow Tile or Masonry Walls -

Use machine

screws and expansion anchors of adequate size

and length or toggle bolts.

9. 

Rough Solid Concrete or Brick Wall -

Use rawl

plugs or lead sleeve anchors of adequate size and 

length.

5. 

Plaster on Metal Studs

(For new construction)

When possible, place wood ground in back of

plaster where cabinets are to hang. Use wood 

screws to anchor steel cleat to wall. Be sure

screw length is of adequate size and length to

anchor securely into the wood ground.

Figure 4-24 Attaching Wall Case to Wall

Top of Cabinet

Hanger

Channel

Steel Cleat

Wood Filler

Cabinet

4.75"

Содержание FISHER HAMILTON MAX/WALL





























































Отзывы: