Thermo Scientific EASY-Spray NG Скачать руководство пользователя страница 41

Страница: 41 / 62

Connecting the EASY-Spray Column Plumbing

Examples of LC Connections to the EASY-Spray Column

Thermo Scientific

EASY-Spray Series Ion Source User Guide

Configuring the EASY-nLC 1200 Plumbing for Two Columns

Use the touch screen on the EASY-nLC 1200 to configure the use of two columns.



To configure the EASY-nLC 1200 for use with two columns

1. On the LC touch screen, press

Maintenance > Devices

2. In the Devices list, press

EASY-nLC (HPLC)

3. Press

Properties

, clear the

One Column Setup

check box, and then press

Apply

The Home page shows the two-column setup (

Figure 17

). For additional instructions,

refer to the LC instrument manual.

Figure 17.

EASY-nLC 1200 touch screen showing a two-column configuration

Connecting an RSLCnano System to the EASY-Spray Column

Follow the appropriate procedure for a one- or two-column setup for an RSLCnano system.
The two-column setup includes a precolumn connected across the autosampler valve.

•

To plumb a one-column setup for the RSLCnano instrument

•

To plumb a two-column setup for the RSLCnano instrument

Two columns

Note

To connect the RSLCnano system to the EASY-Spray column, you must use the

Thermo Scientific Dionex UltiMate 3000 RSLCnano EASY-Spray Application Kit
(P/N 6720.0395).

Содержание EASY-Spray NG































































Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды

Thermo Scientific EASY-Spray NG, Руководство пользователя

Результаты поиска

Содержание EASY-Spray NG

Отзывы:

Похожие инструкции для EASY-Spray NG

Бренды по названию

Популярные бренды