manualshive.com logo in svg

Thermo Scientific Barnstead Smart2Pure 12 UF, Руководство по эксплуатации

Поделиться
Скачать
Thermo Scientific Barnstead Smart2Pure 12 UF Скачать руководство пользователя страница 90

15

 Trouble shooting

80

Smart2Pure

Thermo Scientific

Water leak

• Leaky tubing connection

• Feedwater pressure > 6 bar 

• Component defect (e.g. UV 

quartz tube)

• Check and seal the tubing con-

nection

• Install a pressure reducer

• Contact the Thermo Fisher 

Scientific service department

Dispensed water flow rate is too 
low

• Ultrafilter is blocked

• 0.2 micron final filter is 

blocked

• Air in 0.2 micron final filter

• Replace ultrafilter (see 

“Changing 

the ultrafilter” 

on 

page 71

)

• Replace the 0.2 micron final 

filter

• Vent the 0.2 micron final filter

Error message:
Red LED in second line is light 
up “Limit value Cond.“

• exhausted ultrapure cartridge

• Limiting value set too low

• Replace with new ultrapure 

cartridge

• Check and reset the limiting 

value

Error message:
Red LED in second line is light 
up “Limit value Temp.“

• Temperature in system is too 

high

• Limiting value is set too low

• Feedwater temperature is too 

high

• Reduce temperature by letting 

water flow out

• Check and reset the limiting 

value

• Reduce the feedwater tempera-

ture

Error message:

'

Red LED in second line is light 

up “Status Sens.“

• Interruption in cable to con-

ductivity measuring cell

• Measuring cell defect

• Check the cable and plug con-

nection

• Contact Thermo Scientific for 

replacing

Error message:
Red LED in second line is light 
up “Status Sens.“
The display shows “- -“ with 
audible alarm. 

• Interruption in cable to con-

ductivity measuring cell

• Temperature sensor in mea-

suring cell defect

• Check the cable and plug con-

nector

• Contact Thermo Scientific for 

replacing

Error

Cause

Remedy

Содержание Barnstead Smart2Pure 12 UF















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды