Thermo Scientific Barnstead Smart2Pure 12 UF Скачать руководство пользователя

Страница: 89 / 110

Thermo Scientific

Smart2Pure

Trouble shooting

Contact the service department if you cannot rectify this error.

Error

Cause

Remedy

The system does not start

• No supply of power

• Power pack or system control

defect

• Provide power

• Replace the power pack or sys-

tem control

Dispensing not possible/ storage
tank is empty

• Feedwater supply is closed

• Feedwater and concentrate

water connections are mixed
up

• Feedwater pressure < 1 bar

• Sterile filter blocked

• RO/pretreatment cartridge

blocked.

• Open the feedwater supply line

• Replace connections

• Increase feedwater pressure

• Replace the sterile filter (see

“Replacing the 0.2 μm final fil-
ter”

page 76

)

• Install new RO/pretreatment

cartridge (see

“Replacing the

RO/pretreatment”

page 66

or check RO/pretreatment car-
tridge connections.

Resistance < 18.2 M

·cm/

0.055 μS/cm

• Ultrapure cartridge is

exhausted

• Air in the ultrafilter because

of empty tank

• Check feedwater quality

• Insert new ultrapure cartridge

• Wait until the tank is again

filled and a rinse is triggered

Control panel non responsive

• Microprocessor locked up

• PCB error

• Unplug the mains plug for 5

seconds.

• Contact the Thermo Fisher

Scientific service department

Содержание Barnstead Smart2Pure 12 UF















































































































Результаты поиска

Содержание Barnstead Smart2Pure 12 UF

Отзывы:

Похожие инструкции для Barnstead Smart2Pure 12 UF

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead Smart2Pure 12 UF, Руководство по эксплуатации

Результаты поиска

Содержание Barnstead Smart2Pure 12 UF

Отзывы:

Похожие инструкции для Barnstead Smart2Pure 12 UF

Бренды по названию

Популярные бренды