Thermo Scientific Agilent 1100 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

background image

Thermo Scientific

Agilent 1100 Series Getting Connected Guide for LC Devices

3

2

Connecting the Hardware

This chapter describes how to install the interface boards, connect the Ethernet cables,
and make the contact closure connections required to control an LC/MS
(Agilent LC/Thermo Scientific MS) system from the Xcalibur data system.

Ethernet Communication Kit

To connect the Agilent LC system to a Thermo Scientific mass spectrometer, you must have
the following parts:

• Ethernet Communication Kit (

)

• JetDirect™ 400N LAN card (P/N 00825-01140) or an Agilent LAN card

(Model G1369A)

• Agilent binary-coded decimal (BCD) interface board for contact closure

Contents

•

Ethernet Communication Kit

•

Installing a Network Card in an Agilent Module

•

Connecting the Ethernet Cables

•

Installing the External Contact Interface Board

•

Connecting the Contact Closure Cable

Table 3.

Ethernet Communication Kit (P/N OPTON 30012)

Description

Part number

Agilent BCD (contact interface) board

00012-27714

Contact closure cable with 15-pin connector

00012-27716

Ethernet cable, straight shielded Cat5, 3 m (10 ft)

00012-70008

Fast Ethernet switch, 10T/100Base-TX, 5-port

00825-01-00024

«
...
11
12
13
14
15
...
»

Содержание Agilent 1100 Series

































Отзывы:

Нет отзывов

Похожие инструкции для Agilent 1100 Series

Бренд: MAHLE Страницы: 21

Бренд: B&G Страницы: 3

Бренд: Keiser Страницы: 82

Бренд: Keiser Страницы: 4

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: Gomaco Страницы: 30

Бренд: Panduit Страницы: 4

Бренд: StarDental Страницы: 2

Бренд: USC Страницы: 29

Бренд: NEBO Страницы: 2

Бренд: Furuno Страницы: 2

Labmatic 400.COM

Бренд: LABTEC Страницы: 12

Advisor Guide Pedestrian Signal

Бренд: Campbell Страницы: 14

Бренд: Handicare Страницы: 18

Бренд: Nakamichi Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды