Thermo Scientific 7400 Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 60

background image

7007400 Cryoplus 4-1

Thermo Scientific

Section 4

Maintenance

Valve maintenance is described below.

Warning

These procedures must be performed by qualified service

technicians.

▲

Operation

Normally closed: Valve is closed when solenoid is de-energized, valve is
open when solenoid is energized.

Positioning/Mounting

The valve is designed to perform properly when mounted in any posi-
tion. However, for optimum life and performance, the solenoid should
be mounted upright to reduce the possibility of foreign matter accumu-
lating in the core tube area.

Maintenance

Warning

Turn OFF electrical power supply and de-pressurize valve before

making repairs. It is not necessary to remove valve from pipe line for
repairs.

▲

Cleaning

A periodic cleaning of all solenoid valves(s) is desirable. The time
between cleanings will vary, depending upon media and service condi-
tions. Generally, if the voltage to the coil is correct, sluggish valve opera-
tion, excessive noise, or leakage will indicate that cleaning is required.

Valve Disassembly and Reassembly

De-pressurize valve and turn OFF electrical power supply. Proceed in the
following manner:

1. Remove retaining clip and slide entire solenoid enclosure from

solenoid base sub-assembly.

Caution

When metal retaining clip disengages, it springs upward.

▲

2. Unscrew solenoid base sub-assembly and remove body gasket, core

assembly with rider ring and core spring attached.

«
...
34
35
36
37
38
...
»

Содержание 7400 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 7400 Series

Relion 670 series

Бренд: ABB Страницы: 66

Бренд: Baileigh Industrial Страницы: 40

Бренд: ACDC Страницы: 4

Precision2 HP2 Series

Бренд: B-K lighting Страницы: 6

Бренд: Zero Hand Truck Страницы: 38

Бренд: B-K lighting Страницы: 3

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: Vibration Research Corporation Страницы: 333

Бренд: E-FLOR Страницы: 124

Бренд: Elenco Electronics Страницы: 12

Бренд: GRAVITY Страницы: 2

CardioCare EKG2000

Бренд: Bionet Страницы: 70

Egatronik 51249

Бренд: Ega Master Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды