background image

All installations and services must be performed by qualified service personnel. 

 

42 

DIAGNOSTIC FEATURES 
 

The 50V61 control used on this furnace continuously monitors its operation and the operation of the 
system. 

 

 
If the sensed failure is in the system (external to the control), the red LED will flash in the following flash-
pause sequences to indicate failure status (each flash will last approximately 0.25 seconds, and each 
pause will last approximately 2 seconds): 
 
1 flash, then pause 

 

system lockout (retries or recycles exceeded) 

2 flashes, then pause   

low pressure switch stuck closed 

3 flashes, then pause   

low pressure switch stuck open 

4 flashes, then pause   

open high temperature limit switch 

5 flashes, then pause   

not used 

6 flashes, then pause   

115 V AC power reversed 

7 flashes, then pause   

low flame sense signal 

8 flashes, then pause   

check igniter or improper ground 

9 flashes, then pause   

high pressure switch stuck open 

Continuous flash 

 

 

flame sensed with gas valve de-energized 

 
The LED will also flash once at power-up. 
 
A green LED indicator is also present to obtain an estimate of the air flowrate (in CFM) produced by the 
house air blower.  This LED cycles regularly by providing a constant light, followed by a sequence of 
flashes.  Each flash can be translated to programmed CFM by using the following: 
 
1 flash per 100(programmed) CFM 
 
 

: Power must be disconnected before servicing. 

 

 

Содержание CDX1-100N




























































Отзывы: