Thermedx FluidSmart Скачать руководство пользователя страница 8

Страница: 8 / 39

8 |

P a g e

Part Number - 00824 Revision K, DCO 2017-0074

, LLC

Section 4 – Principle of Operation



The FluidSmart

uses a peristaltic pump to pressurize fluids from fluid bags hanging on

either side of the unit.



Fluid is conducted through a warming mechanism that uses infrared lamps to warm the

irrigation fluids on demand to a specified set temperature, generally approximating body

temperature. The warming mechanism may be enabled during approved procedures.



Flow rates are calculated by counting pump rotations and tracking changes in the weight

of fluid bags via load cells associated with the fluid bag hooks.



IR (infrared) temperature sensors are used to measure the fluid temperature in a non-

contact method. Three sensors are used in the warming mechanism (beginning, middle,

and end of fluid path). Two additional temperature monitors are used downstream of the

warming mechanism as a safety measure independent of software.



Using the flow rate, inlet temperature, and desired set-point temperature, the IR lamp

power is calculated. The warming process is adjusted as needed based on feedback from

temperature sensors.



Temperature measurements displayed by the system are readings of fluid temperature at

the exit of the warming mechanism. These readings do not account for temperature losses

as fluid passes through the disposable tubing.



Fluid volume instilled (inflow) and fluid deficit are determined on the basis of weight using

load cells in the fluid bag hooks and suction canister ring.



Fluid pressure is monitored via pressure transducers. Redundant sensors are used for safe

operation. Pressure measurements displayed by the system are readings at the system

and may not reflect the pressure at the surgical site.



The system operates via pressure control. The system will attempt to maintain the

specified pressure (i.e. 100mmHg). Pump speed will increase or decrease accordingly.



On the basis of the selected clinical discipline and procedure the system will enable
procedure specific pressure, flow, warming, and/or deficit monitoring alarm values.

The default values are user adjustable within specified safety limits. Not all

features are available for all procedures.

Содержание FluidSmart








































Результаты поиска

Содержание FluidSmart

Отзывы:

Бренды по названию

Популярные бренды

Thermedx FluidSmart, Руководство по эксплуатации

Результаты поиска

Содержание FluidSmart

Отзывы:

Бренды по названию

Популярные бренды