manualshive.com logo in svg

thermastor Quest 335, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
thermastor Quest 335 Скачать руководство пользователя страница 5

4. Installation 

4.1 Location 

The Quest 335 Dehumidifer can be installed in a variety of locations to meet the owner’s needs as listed below. In all 

cases keep the following cautions in mind: 
•  Place the Quest 335 Dehumidifer on supports that raise the base of the unit 6” above the secondary drain pan so a 

P-trap can be installed. See Section 4.3. 

•  The Quest 335 Dehumidifer may be suspended with steel hanger, straps, or a suitable alternative from structural 

members, unit must be supported from underneath. Don’t hang from sides or ends. See section 4.4 

•  If installing on ground, use included plugs to cover hanging locations on top of the machine. 
•  If hanging machine in air, use included plugs to cover holes in base pan for leveling feet. 

4.2 Electrical Requirements 

The Quest 335 Dehumidifer plugs into NEMA rated receptacles. The amp draws for each unit under normal operating 

conditions are listed on page 4. A ground fault interrupter protected circuit is required. 
Install the remote hygrostat in a central area of the structure where it will sense the relative humidity of the structure 

accurately. Do not install the hygrostat where it may not accurately sense the relative humidity such as near HVAC 

supply registers, near exterior doors, or near a pool or spa. The installer must supply the wiring between the Quest 335 

Dehumidifer and the hygrostat. Be sure to safely route the control wiring to prevent damage during installation. Be 

careful not to cross the wires when connecting the Quest 335 Dehumidifer and the remote hygrostat. 
The remote controls of the Quest 335 Dehumidifer are powered by a low voltage circuit (24 VAC) and must NEVER 

contact or be connected to a high voltage circuit. The control terminals and remote control are labeled and numbered to 

prevent confusion. Be sure to consult the electrical schematic in this manual or inside the access panel of the Quest 335 

Dehumidifer before making the control connections. 

 CAUTION!  Always disconnect the Quest 335 from a power source when working with the low 

voltage control wires. 

5 

Содержание Quest 335

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды