Power source:
240V,
single phase power into
contactor box shall be provided from an
NRTL
--11
..
��1
Listed
(UL, ETL, TUV,
etc.) load center with
branch circuit protectors
SAUNA CONTROL
F-2T
LOAD CENTER
(Supplied by Electrician)
Line 2 ---------------------
T- - --------- ,
'
'
Line 1 - - - - - - - - : 1 - -
"t-
2
- - - - � 1
'.
2
1,io14ol l4ol4ol
G
N
'
l
�
,
'
'
L1
d
l2
L2
'
'
'
'
,
Grn,ad
,
..
·······················.··.'l
......
!
�---·
---;-' ---------;----,;
CONTACTOR BOX
FX404
h--'-"""-i=- ------ --- ---;
Thermostat
Room Light
Switch
OFF ON
'
'
--- -----.J
L N
'
'
' '
�
-
t1
_ --- ---�--
:
'
'
'
''
'
'
All Contactor
to Control
wiring is
#14 wire
Terminal Block
.1.
LEGEND
Factory wiring
'
'
•
G
•
'
'
.
ii i
TTTT
!
cOntacto�
i
'
'
'
• • • •
L1
L1
L2
L2
• • • •
:#14
:#14
•
•
A1
A2
• •
To sauna interior light.
120V, 100W maximum
Installation wiring
-----------
lntertek ��:����; TO
4002l90 CERTIFIED TO
Quick Connect
c::::::,
SAUNA HEATER CONNECTIONS
LISTED
CAN/CSA STD
PANEL
C22.2 NO. 164
Wire Nut
D
Figure 5
CLUB MODEL HEATER (240 V 1 PH)
HEATER
WATTS VOLTS AMP
BREAKER WIRE SIZE
MODEL
DRAW
SIZE
breaker to
TO USE
load center
HCT105-1
10,000
240/1
41.7
50
#6 copper
HCT120-1
12,600
240/1
52.7
60
#6 copper
HCT144-1
14,800
240/1 61.7
70
#4 copper
SAUNA HEATER WIRING AND HOOKUP -
ALSO REFER TO FIGURE 1
Refer to chart above for proper wire size and
amperage. See page 3 for required clearances. Use
copper wire from load center to wall-mounted
contactor. Supply cable must have 5 wires including
insulated neutral plus separate ground.
Use 90
°
C copper wire from contactor to control
and from control to room light. Also use 90
°
C copper
wire from contactor to Sauna heater (within seal
tight flex conduit), and connect to junction box at
heater with 90
°
connector.
Connect to the noted terminals and connect
ground wire to marked terminal. (Cover plate on
heater must be removed first).
WIRE SIZE
WIRE SIZE
CONTROL CONT ACTOR
load center
contactor to heater
3.75" X 2.5"
6
11
X 4
11
X 8
11
to contactor
X 9.25"
(4) #10
(4) #10
F-2T
FX404
(4) #10
(4) #10
F-2T
FX404
(4) #8
(4) #8
F-2T
FX404
Important! Follow wiring instructions carefully to
prevent shorting of glass fuses in contactor.
Be sure there are no bare wires or shorts.
If the contactor is shorted out it will be the
responsibility of the electrical contractor to replace
it!
If connection to heater will be made at a later time,
bring flex into Sauna room 4-6" from floor, and leave
3' of flex for hookup (can be cut to right length later).
Before testing heater, fill rock cavity with igneous
stones provided with heater and fasten metal rock
guard at top of heater. (See gen. info concerning
washing and placing of stones.)
4
81205_NC
