background image

7.

 Connect the inlet water pipe, please remember to fix a filter net inside the nut of 

water pipe, please make sure the water is turned off.

oPeratIoN INstructIoNs

1.  For the first time operating the appliance, please allow water to flow through the tap  
 

before turning on power to the appliance.

2.  While the handle faces to 

 the appliance will keep closed. When the shank  is    

 

rotated to  

C

  cold water will come out. Rotate the handle shank  

 to 

H

 to activate the hot water with the indicating light displaying red.

3.  Rotate the handle to adjust the outlet water flow.

4.  The nozzle is rotatable in 360°.

Maintenance

note: always turn off the power supply before servicing your unit. 
the thermaQ designer tap does not require any regular maintenance. however, to 
ensure consistent water flow, the following maintenance is recommended.

1.  Periodically remove scale and dirt that may build up at the aerator of the faucet or in  
 

the sprinkler. 

2.  The filter net at the water inlet should be cleaned from time to time. Please turn off    
 

the water flow before doing this.

3.  If you will not use this appliance for long time, please disconnect the plug.

Trouble-Shooting

Hold-Down Nut

Table

Board

Water

Inlet

Pipe

Power

Cord

Rubber Mat

Pedestal

Hand

Shank

Hold-Down Nut

Table

Board

Water

Inlet

Pipe

Power

Cord

Rubber Mat

Pedestal

Hand

Shank

Fig 7.

 

a.

 Power cord connect 

above the table-board.      

Fig 7.

 

B.

 Power cord connect 

under the table-board.      

PackINg 

lIst

Excellence in Hot Water Technology.

10

11

 

ThermaQ Specification Hotline 01924 270847

ProBlems

PossIBle causes

correctIve actIoNs

No hot water comes 

out while the 

appliance is turn on.

• 

Inlet water flow is less than 1L/min.

• 

no power supply.

• 

Increase the inlet water flow.

• 

Check wire & power connection.

outlet water temp.  

is too high.

• 

Water flow too small.

• 

Increase inlet water flow.

outlet water temp.  

is too low.

• 

Water flow too high.

• 

Reduce water flow.

outlet water flow.  

is too low.

• 

Inlet strainer or shower clogged.

• 

Clean strainer and shower

outlet water flow.  

is too high.

• 

Sprinkler blocked.

• 

Clean the sprinkler

Item

uNIt

QuaNtIty

Electric Hot Water Tap.

Unit

1

User Manual

Copy

1

Pedestal

Unit

1

Rubber Mat.

Piece

1

Hold-Down nut

1

1

Rubber Ring & Rubber Filter net.

Set

1

Содержание Designer Tap







Отзывы: