Thermal Dynamics PAK Master 150XL Скачать руководство пользователя

Страница: 40 / 90

REPLACEMENT PROCEDURES

5-2

Manual 0-2728

WARNING

Disconnect primary power from the source before
opening or disassembling the power supply. Make
sure AC indicator on the Power Supply front panel
is OFF.

5.04 Major External Parts

Replacement

NOTE

Refer to Section 6.03 for parts list and overall de-
tail drawing.

A. Left or Right Side Panel Replacement

1. Remove input power from the unit.

2. Loosen the two bottom screws in the slotted holes

of the desired Side Panel (viewed from the front
of the unit).

3. Remove the remaining screws which secure the

Side Panel to the Power Supply.

4. Pull the top of the Side Panel out and then lift up

to remove the panel from the Power Supply a
short distance (see NOTE).

NOTE

There is a ground wire connection to the Side Panel
on the inside of the unit.

5. Remove the nut securing the ground wire to the

side panel and remove the ground wire.

6. Remove Side Panel from unit and set aside.

A-03058

NOTE

Art may differ

from actual unit.

Figure 5-1 Side Panel Removal

7. Install the replacement Side Panel by reversing

the above procedure doing the following:

a. Reconnect the ground wire to the Side Panel,

if disconnected.

b. Place the Side Panel onto the frame and slide

the top edge under the lip on the Top Panel.

c. Reinstall all the screws to secure the Side Panel.

B. Top Panel Replacement

1. Remove the Left Side Panel per Section 5.04-A.

2. Remove the screws securing the Top Panel to the

side and rear panels.

3. Locate and remove the nut securing the Top Panel

to the center chassis.

4. Slide the Top Panel stud out of the center chassis

hole.

5. Install the replacement Top Panel by reversing the

above procedure.

C. Work Cable Replacement

1. Remove Right Side Panel per Section 5.04-A.

2. Remove the work cable strain relief from the Front

Panel.

3. Disconnect work cable connection from E8 on Pi-

lot Output PC Board.

4. Pull the work cable through the Current Sense PC

Board and then through the Front Panel, then re-
move from unit.

5. Install the replacement work cable by reversing

the above procedure.

D. Torch & Leads Assembly Replacement

1. Open the Access Panel per Section 5.05-E.

2. Disconnect all hoses and the cable from the bulk-

head.

3. Disconnect Shield Wire from Shield Stud, if

present on Torch lead.

4. Install the replacement Torch Assembly by revers-

ing the above procedure, keeping in mind the fol-
lowing:

a. Connect the bottom hoses first.

b. The two fittings on the right side of the bulk-

head (when viewed from the front of unit) are
for left hand hoses; the two fittings on the left
are for right hand hoses.

Содержание PAK Master 150XL



























































































Результаты поиска

Содержание PAK Master 150XL

Отзывы:

Похожие инструкции для PAK Master 150XL

Бренды по названию

Популярные бренды

Thermal Dynamics PAK Master 150XL, Руководство по обслуживанию

Результаты поиска

Содержание PAK Master 150XL

Отзывы:

Похожие инструкции для PAK Master 150XL

Бренды по названию

Популярные бренды