Thermal Dynamics 1-4200-6 страница 8 Скачать руководство пользователя

Страница: 8 / 44

CUTMASTER 10MM, 12MM

GENERAL INFORMATION 1-2 Manual 0-5197AD

ELECTRIC SHOCK

Electric Shock can injure or kill. The plasma arc process uses and

produces high voltage electrical energy. This electric energy can

cause severe or fatal shock to the operator or others in the workplace.

• Never touch any parts that are electrically “live” or “hot.”
• Wear dry gloves and clothing. Insulate yourself from the

workpiece or other parts of the welding circuit.

•  Repair or replace all worn or damaged parts.
•  Extra care must be taken when the workplace is moist or damp.
•  Install and maintain equipment according to NEC code, refer to

item 9 in Subsection 1.03, Publications on page 1-4.

• Disconnect power source before performing any service or

repairs.

• Read and follow all the instructions in the Operating Manual.

FIRE AND EXPLOSION

Fire and explosion can be caused by hot slag, sparks, or the plasma arc.

• Be sure there is no combustible or flammable material in the

workplace. Any material that cannot be removed must be

protected.

• Ventilate all flammable or explosive vapors from the workplace.
• Do not cut or weld on containers that may have held combus

tibles.

• Provide a fire watch when working in an area where fire hazards

may exist.

• Hydrogen gas may be formed and trapped under aluminum

workpieces when they are cut underwater or while using a water

table. DO NOT cut aluminum alloys underwater or on a water

table unless the hydrogen gas can be eliminated or dissipated.

Trapped hydrogen gas that is ignited will cause an explosion.

NOISE

Noise can cause permanent hearing loss. Plasma arc processes can

cause noise levels to exceed safe limits. You must protect your ears

from loud noise to prevent permanent loss of hearing.

• To protect your hearing from loud noise, wear protective ear

plugs and/or ear muffs. Protect others in the workplace.

• Noise levels should be measured to be sure the decibels (sound)

do not exceed safe levels.

• For information on how to test for noise, see item 1 in Subsec

tion 1.03, Publications, in this manual.

PLASMA ARC RAYS

Plasma Arc Rays can injure your eyes and burn your skin. The plasma

arc process produces very bright ultra violet and infrared light. These

arc rays will damage your eyes and burn your skin if you are not

properly protected.

•

To protect your eyes, always wear a welding helmet or

shield. Also always wear safety glasses with side shields,

goggles or other protective eye wear.

•

Wear welding gloves and suitable clothing to protect your

skin from the arc rays and sparks.

• Keep helmet and safety glasses in good condition. Replace

lenses when cracked, chipped or dirty.

•

Protect others in the work area from the arc rays. Use

protective booths, screens or shields.

•

Use the shade of lens as suggested in the following chart.

NOTE

These values apply where the actual arc is clearly

seen. Experience has shown that lighter filters may

be used when the arc is hidden by the workpiece.

Содержание 1-4200-6













































Результаты поиска

Содержание 1-4200-6

Отзывы:

Похожие инструкции для 1-4200-6

Бренды по названию

Популярные бренды

Thermal Dynamics 1-4200-6, Руководство по эксплуатации

Результаты поиска

Содержание 1-4200-6

Отзывы:

Похожие инструкции для 1-4200-6

Бренды по названию

Популярные бренды