Thermal Dynamics 1-4200-6 страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 44

background image

CUTMASTER 10MM, 12MM

INSTALLATION 3-2 Manual 0-5197AD

3.03 Air Supply Connections

A. Connecting Air Supply to Unit

The connection is the same for compressed air or indus-

trial compressed air in gas cylinders.

1. Connect the gas line to the compressed air inlet

port at the appropriate pressure.

Art # A-10223

Air Inlet, 1/4” NPT

On/Off

Switch

Figure 3-1 - Gas Connection to Compressed Air Input

1/4 NPT
Hose Fitting

Hose
Clamp

Gas Supply Hose

Filter Hose

Single-Stage

Filter Kit

No. 7-7507

ART# A-10675

Figure 3-2 - Optional Single - Stage Filter Installation for

Compressed Air Input

B. Using Industrial Compressed Air In Gas Cylinders

When using industrial compressed air in gas cylinders

as the gas supply:

1. Refer to the manufacturer’s specifications for

installation and maintenance procedures for high

pressure gas regulators.

2. Examine the cylinder valves to be sure they are

clean and free of oil, grease or any foreign mate-

rial. Briefly open each cylinder valve to blow out

any dust which may be present.

3. The cylinder must be equipped with an adjust-

able high-pressure regulator capable of outlet

pressures up to 100 psi (6.9 bar) maximum and

flows of at least 250 scfh [Standard cubic foot

per hour] (120 lpm) [liter per minute].

4. Connect gas supply hose to the cylinder.

NOTE

Pressure should be set at 100 psi (6.9 bar) at

the high pressure gas cylinder regulator.
Supply hose must be at least 1/4 inch (6mm)

internal diameter.
For a secure seal, apply thread sealant to the

fitting threads, according to manufacturer's

instructions.

DO NOT

use Teflon tape as a

thread sealer, as small particles of the tape

may break off and block the small gas pas-

sages in the torch.

«
...
20
21
22
23
24
...
»

Содержание 1-4200-6













































Отзывы:

Нет отзывов

Похожие инструкции для 1-4200-6

Бренд: Mackie Страницы: 14

Gemini GEM-X255

Бренд: NAPCO Страницы: 40

Бренд: NAPCO Страницы: 16

Бренд: NAPCO Страницы: 6

Бренд: VeGue Страницы: 12

Бренд: GREER Company Страницы: 35

Бренд: Velleman Страницы: 18

Бренд: JBL Страницы: 10

Бренд: Metrix Страницы: 4

Бренд: Teac Страницы: 23

Бренд: Real-El Страницы: 8

Бренд: NAPCO Страницы: 16

Point-of-Use Drinking Water System

Бренд: R-Can Страницы: 12

BeoSound 3000 2671

Бренд: Bang & Olufsen Страницы: 68

Бренд: Velleman Страницы: 12

Pursuit PRO-9649N

Бренд: Audiovox Страницы: 8

Бренд: Corbin Russwin Страницы: 8

bigben XD Party Box 25

Бренд: iDance Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды