THERMACUT EX-TRACK Скачать руководство пользователя страница 21

Страница: 21 / 121

EX-TRACK

Operator manual, Revision T-1

Gas cylinders which contain gas under high pressure can
rupture and explode if damaged.

•

Handle and use compressed gas cylinders in accordance
with local or national codes.

•

Never allow electrical contact between the plasma arc
and a cylinder.

•

Never expose cylinders to excessive heat, sparks, slag or
flames.

CAUTION WHEN CUTTING
AROUND GAS CYLINDERS

Plasma Arc Cutting

Current

Protection glass

shade number*

Up to 150A

ISO (DIN) 11

150A to 250A

ISO (DIN) 12

250A to 400A

ISO (DIN) 13

OVER 400A

ISO (DIN) 14

* According to ISO 4850:1979

Induction heating of certain materials, adhesives, and fluxes
may cause fumes or smoke.

Breathing the fumes and smoke can be hazardous to your
health

•

Keep your face out of the smoke, do not breathe the
fumes.

•

Use local exhaust ventilation for fume removal.

•

If ventilation is poor, wear an approved air-supplied
respirator.

SMOKE AND GASES CAN BE HAZARDOUS

•

Work in a confined space only if it is well ventilated,
or while wearing an air-supplied respirator. The
smoke and gases from the cutting/gouging process
can displace air and lower the oxygen level causing
injury or death.

•

Monitor the breathable air quality as required.

MAGNETIC FIELD CAN
AFFECT PACEMAKERS

•

People with pacemakers/hearing aids should avoid
close contact with plasma arc power supply.

•

People with pacemakers/hearing aids should consult
their doctor before operating plasma arc power
supply.

Do not exceed the
recommended duty cycle,

this can lead to overheating and
cause damage to the system.

•

Allow a suitable cooling off period with high demand
usage.

•

Observe the duty cycle rating shown on the label
attached to the system.

PLASMA CUTTING CAN
CAUSE INTERFERENCE

•

Electromagnetic energy can interfere with sensitive
electronic equipment such as computers, or
computer-driven equipment.

•

Ensure that all equipment in the cutting area is
electromagnetically compatible.

•

Ensure that the plasma arc cutting system is installed
and positioned in accordance with this manual.

Содержание EX-TRACK


























































































































Результаты поиска

Содержание EX-TRACK

Отзывы:

Похожие инструкции для EX-TRACK

Бренды по названию

Популярные бренды

THERMACUT EX-TRACK, Руководство оператора

Результаты поиска

Содержание EX-TRACK

Отзывы:

Похожие инструкции для EX-TRACK

Бренды по названию

Популярные бренды