Therma Q AGDIR 0120 Скачать руководство пользователя страница 5

ISSUE 2016 Rev 1 - Installation Manual 

ThermaQ 

 

Component Checklist 

 
General Installation Requirements 
 
The cylinder must be installed, commissioned and maintained by a competent installer holding their G3 unvented qualification, or being a 
member of a competent persons’ scheme. Once the unit is installed and commissioned, the user must be given an explanation of the operation 
of the cylinder, and be given this installation manual for future reference. 
 
Storage and Handling 
 
Care must be taken when handling the product. Given the weight of the unit, use more than 1 person for carrying where appropriate, and be 
sure to comply with safe working practices and lifting techniques to avoid injury or product damage. The cylinder must be stored upright in its 
original packaging, on a secure, level surface within a dry and frost-free environment. 
 
Siting the Unit 
 
The cylinder must be installed vertically on a flat base, capable of supporting the weight of the cylinder when full. The minimum 
recommended cupboard size is 650mm square. 
 
Nominal diameter of cylinder is 545mm. 
 
Areas that are subject to freezing should be avoided, however if the cylinder is outside of the heated area of the dwelling, such as a garage or 
outbuilding, ensure that frost protection is provided, and exposed pipework is insulated. Pipe lengths should be kept to a minimum to ensure 
minimal losses. For each metre an outlet is above the cylinder, the pressure will be reduced by 0.1 bar. 
 
It is important to have room for access to the valves and controls of the cylinder, in order that they can be serviced and maintained. The 
immersion heaters are 375mm in length, and space should be provided for future removal and replacement. 
 

Components(s) 

Direct  Indirect 

Solar Indirect 

Solar Twin 

Status 

Manual / Benchmark 

 

 

 

 

Loose 

ERP Label 

 

 

 

 

Loose 

Inlet Control Set 

 

 

 

 

Loose 

T & P Valve 

 

 

 

 

Fitted 

T & P Insulation Cover 

 

 

 

 

Loose 

Tundish 

 

 

 

 

Loose 

Immersion Heater(s) 

 

 

 

 

Fitted 

Control / Limit Stat 

 

 

 

 

Loose 

Single Limit Stat 

 

 

 

 

Loose 

Two Port Zone Valve 

 

 

 

 

Loose 

Solar Cable Grommet 

 

 

 

 

Loose 

Содержание AGDIR 0120























Отзывы: