Theben 4940301 Скачать руководство пользователя страница 58

Страница: 58 / 88

ETS parameters

Manual DALI gateway S64 KNX/S128 KNX

Value on DALI Power Fail (System Failure

Level)

0..100%

[100]

Last value

Use this parameter to set the value of a lamp after a loss of DALI power. The value is saved on

the ECG and the device automatically changes to the value when a power loss occurs.
Value on ECG Power Recovery (Power On

Level)

0..100% [

100

]

Last value

Use this parameter to set the value of a lamp after a return of ECG power supply. The value is

saved on the ECG and the device automatically changes to the value when power is restored.

Calculation of Dimming Values

logarythmic

linear

Sets the dimming curve for the ECG is adjusted.

Control ECG Power Line via Object

None

Energy Saving Object 1.. 16

Here you define the object with which the power supply is to be switched off. This parameter

is only visible if this function was previously set on the General



Special Functions parameter

page, see 9.1 General.

Operating hours Calculation

Yes

This parameter can be used to set whether an individual operating hour count for the ECG is

desired.
Operating hours Limit value (hours)

(Calculation for operating hours).

1 h..200.000 h

[4000 h]

This parameter is used to set the lamp life at which an individual warning is sent.

Type of the error object

1 bit

1 byte

Here you can define whether the error is to be reported in the form of a bit (Alarm DPT 1.005)

or via a byte object with the information about lamp or ballast errors, see 9.1 General.

Note:

The 1 Byte object is a NON DPT type and will not be implemented in future versions.

Содержание 4940301

























































































Результаты поиска

Содержание 4940301

Отзывы:

Похожие инструкции для 4940301

Бренды по названию

Популярные бренды

Theben 4940301, Руководство пользователя

Результаты поиска

Содержание 4940301

Отзывы:

Похожие инструкции для 4940301

Бренды по названию

Популярные бренды