Relax, because you have
just successfully built your
own Bluetooth Speaker
that will not only connect
wirelessly to your mobile
phone or suitable music
player, but is a totally
accurate replica of the
Pip-Boy stand as seen in
Vault-Tec vaults across
the land. Display your
Pip-Boy, play your music,
answer calls and use as a
handsfree speakerphone
and enjoy.
42
Don’t relax for too long,
because it’s time to display
your
Pip-Boy 2000 Mk VI
.
Carefully slide the Pip-boy
into place fully on to the
Display Stand so that the
Large Cuff
is at the
support end and rotate so
that the screen is vertical.
43
Pip-Boy Display Stand Replica
Pip-Boy 2000 Mk VI
Large Cuff
POWERING UP AND POWERING DOWN
To power up the stand, connect the USB-C lead to a
suitable power supply and plug it into either of the two
USB-C Sockets
on the base of the
Stand
. When the
Stand
is powered up and is not connected with another
Bluetooth device, the
Top Indicator
flashes green. When
the
Stand
is connected with another Bluetooth device,
the
Bottom Indicator
double-flashes blue.
Press and hold the
Power Button
to power down or
power up the Stand when the USB-C lead is plugged in.
JOG BUTTON FUNCTIONALITY
The
Jog Button
is a five-way jog button and can be either
pressed in or jogged up, down, left or right. The
Stand
does not have to be paired with or connected to any
devices if you only want to play any of the 10 built-in
Overseer voice clips. Press or double press, or jog left,
right or up or down or double jog in each direction to play
each of the clips.
CONNECTING AND PAIRING THE STAND
In order for the
Stand
to play music, it must be paired with
and connected to a Bluetooth-enabled music streaming
device. When paired with a mobile phone, the
Stand
can
also act as a handsfree speakerphone.
To pair and connect the
Stand
:
• Activate Bluetooth on your music streaming device.
• Press and hold the
Jog Button
until the
Stand
says,
“
Waiting for Bluetooth connection
”, and the
Bottom
and
Top Indicators
alternately flash green and blue.
• Make sure your music streaming device is searching
for devices.
• Within 60 Seconds, your music streaming device
should show
Pip-Boy Stand
in its list of available
devices.
• Select
Pip-Boy Stand
from the list.
• Your music streaming device should report
that it is pairing.
• Once the
Stand
is paired it will emit a short
high-pitched tone and say, “
Connected
”.
• The
Bottom Indicator
will double flash blue
while the Stand is connected.
Typically the
Stand’s
Bluetooth radio will work
with a range of up to five metres. Atmospheric
conditions and dense solid objects (such as
walls) can reduce this range. If the music
streaming device moves out of range of the
Stand
, then the connection will be broken.
However, the
Stand
and the music streaming
device will not forget their pairing and as soon
as they move back within range of each other
they will automatically reconnect.
Once the
Stand
is paired with a device, it
will remember that device and the device will
remember the
Stand
. Each time it is powered
on and the other device is within range, it should
automatically reconnect to the paired device and say,
“
Connected
”. If a paired device does not automatically
reconnect, single-click the Stand’s
Jog Button
.
PLAYING MUSIC
To play music, double-click the
Jog Button
. If music
doesn’t start playing automatically, browse to the music on
your music player and select play. Once the music is
playing through the
Stand
, double-clicking the
Jog Button
will pause or play the music.
While playing music, the
Jog Button’s
functions are
altered slightly. Instead of voice clips, jog right and jog left
will skip tracks forward and back respectively.
VOLUME CONTROL
Whilst paired, the volume of the
Stand’s
speaker may be
adjusted by holding the
Jog Button
up or down. A low beep
is played for each volume step and a higher beep is heard
when the volume is at its maximum or minimum setting.
NOTE:
Depending on the paired device, adjusting the
music playback volume on the paired device may affect
the volume of the music streaming through the Stand
.
UNPAIRING
To unpair the
Stand
from a device that it has been paired
with, browse to the device’s Bluetooth settings menu,
select
Pip-Boy Stand
from the paired devices list and
select “unpair” or “forget”.
Note: The exact sequence for unpairing will vary from
device to device, so please consult your device’s manual
for the correct procedure.
CARE INSTRUCTIONS
The
Stand
is a high tech communications device and
should be handled with care. Clean only with a soft, slightly
damp cloth and never immerse in water.
To protect the
Stand
while not on display, store it
out of direct sunlight. The Stand should only be used
when its operating temperature is between 10˚C and
40˚C (50˚F to 100˚F).
Power Button
Jog Button
USB-C socket
Mic Port
Indicators
OPERATING INSTRUCTIONS
