manualshive.com logo in svg

TFT Typhoon, Руководство пользователя, Страница: 4 / 36

Поделиться
Скачать
TFT Typhoon Скачать руководство пользователя страница 4

©Copyright Task Force Tips LLC  2004-2018 

LIY-050 January 23, 2018 Rev13

4

1.0 MEANING OF SAFETY  SIGNAL WORDS

A safety related message is identifi ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular 
hazard. Per ANSI standard Z535.6-2006, the defi nitions of the four signal words are as follows:

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious 
injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious 
injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor 
or moderate injury.

NOTICE

NOTICE is used to address practices not related to personal injury.

2.0  SAFETY

The operation of this monitor can be dangerous. The following must be observed at all times.

WARNING

Injury or death may occur by attempting to use a damaged monitor.  Before using the monitor 
inspect it for damage resulting from:

• Failure to drain monitor followed by exposure to freezing conditions
• Exposure of monitor to temperatures in excess of 160 degrees F
• Structural damage caused by over-pressurization
• Missing parts, physical abuse, exposure to severe chemicals
• Deformed or cracked fl anges damaged as a result of improper installation

- Excessive bolt torque
- Wrong tightening sequence

WARNING

Injury can result from an inadequately supported monitor. The monitor mount must be capable of 
supporting 1100 lbs (500 kg) of nozzle reaction force.

WARNING

The stream exiting a monitor is very powerful and capable of causing injury and property damage. 
Make sure the monitor is securely attached to the base and pointing in a safe direction before 
water to the monitor is turned on. Use care in directing the stream.

WARNING

The monitor may be damaged if frozen while containing suffi

  cient amounts of water. Such damage 

may be diffi

  cult to detect visually and can lead to possible injury or death. Any time the monitor is 

subject to possible damage from freezing, it must be hydrostatically tested by qualifi ed personnel 
before being considered safe for use.

WARNING

Do not connect AC voltage to this remote control device. This RC device is intended for operation 
from DC power supplies with voltages from 12-24 VDC. Using the wrong power source may cause 
electrocution or ignition resulting in serious injury or death.

CAUTION

The electric Typhoon RC may be remotely operated. The electric drives are current limited but 
may still produce enough force to cause injury. Keep hands and fi ngers away from pinch points 
on the monitor.

CAUTION

Do not use the manual override knobs while the electric controls are in operation. The electric 
drives produce enough torque to cause injury.

CAUTION

Operating a monitor beyond it’s maximum limits may result in injury. Always stay within the safe 
operating fl ow and pressure limits stated on the product.

CAUTION

On many vehicle installations, the monitor is the highest point on the apparatus. Be sure there 
is suffi

  cient clearance to safely pass under any doors or overhead obstructions. Always check 

parked position of the monitor before moving.

NOTICE

All replacement parts must be obtained from the manufacturer to assure proper operation of the 
product, and to maintain approval of the device.

Содержание Typhoon





































Отзывы:

Нет отзывов