manualshive.com logo in svg

TFT Typhoon, Руководство пользователя, Страница: 14 / 36

Поделиться
Скачать
TFT Typhoon Скачать руководство пользователя страница 14

©Copyright Task Force Tips LLC  2004-2018 

LIY-050 January 23, 2018 Rev13

14

4.2 INLET MOUNTING AND TRAVEL RANGES
4.2.1 INLET FITTING OR EXTEND-A-GUN INSTALLATION

The Typhoon Monitor is available with various inlet fi ttings as shown in fi g 3.3. When the inlet fi ttings are used see fi gure 4.2.1A 
for the addition to overall height. The Typhoon Monitor also connects directly to TFT’s Extend-A-Gun RC3 or RC4. The fi ttings and 
Extend-A-Gun RC are attached to the monitor by means of a threaded joint with an o-ring seal. 

TWO PIECE CLAMP ROTATIONAL LOCK INSTALLATION INSTRUCTIONS 
(without tapped holes):

1) Assemble Clamps and place loosely on Extend-A-Gun.

A) Apply VSA-125 blue Loctite to threads on Cylinder Nut.
B) Loosely install Screws, Washers and Cylinder Nuts on Clamp.
C) Grooves on heads of Cylinder Nuts indicate alignment of threaded holes.
D) Place Clamp assembly over male threads of Extend-A-Gun outlet.
E) Heads of Cylinder Nuts must be on top side of Clamps.

2) Screw monitor onto Extend-A-Gun RC until threaded joint bottoms out. 

 

NOTICE

 Make sure the Clamps are not tight enough to prevent the monitor Base from bottoming out. The 
monitor will leak if it does not bottom out in this step.

 A) DO NOT USE PIPE SEALANT OR LOCTITE ON THE INLET BASE THREADS. 

 

NOTICE

 These threads are sealed with an O-ring. The use of thread locking compounds will make removal 
diffi

  cult.

 3) Unscrew monitor until the “Straight Ahead Reference Mark” is facing the desired direction.

A) Monitor may be unscrewed up to one full turn from the bottomed out position.

 

NOTICE

 Monitor will leak if unthreaded more than one full rotation from bottomed-out condition.

 4) Rotate the Clamps to the desired orientation.

A) Ensure that Clamp assembly does not interfere with RC monitor Power/Com Cable.

5) Tighten each Screw gradually until both are fi nger tight with approximately equal spacing between opposite ends of Clamps.
6)  Carefully  tighten  each  Screw  one  additional  turn  using  a  5/32  hex  wrench  by  alternating  to  the  opposite  Screw  in  half  turn 
increments. 

 

NOTICE

 Over tightening the Screws will damage Screws and Clamps.

 

STRAIGHT AHEAD
REFERENCE MARK

MONITOR INLET

10-32 X 1 1/4 LONG

SOCKET HEAD SCREW
VT10-32SH1.2
(2) PLACES

WASHER
VW360X200-04
(2) PLACES

CHAMFER MATES

WITH TOP OF CLAMP

WIRE SKIRT

NOT SHOWN

FOR ILLUSTRATION

PURPOSES

MONITOR BASE CLAMP
(2) PLACES

INLET FITTING MOUNTED

TO EXTEND-A-GUN

OTHERS ARE SIMILAR

CHAMFER MATES

WITH BOTTOM OF CLAMP

CYLINDER NUT

Y4437

(2) PLACES

EQUAL

SPACING

1 TURN PAST

FINGER TIGHT

Содержание Typhoon





































Отзывы:

Нет отзывов