TFA 60.2029.10, Инструкция по эксплуатации

Страница: 9 / 25

13 12
Alarm clock function
Press the ALARM 1 (Fig.1-H) or ALARM 2 (Fig.1-G) button in normal mode. The last adjusted
alarm time will be displayed for a short moment. The corresponding alarm symbol flashes.
Alarm time setting
Press and hold the ALARM 1 (Fig.1-H) button in normal mode to enter the alarm setting mode.
The hour digit and the alarm symbol 1 (Fig.1-J) start blinking.
Press the or button (Fig.1-E, Fig.1-K) to set the hours.
Confirm the setting with the ALARM 1 button.
Set the minutes in the same way.
Confirm the setting with the ALARM 1 button.
ALARM 2 can be adjusted in the same way.
Activate and deactivate the alarm
Press the ALARM 1 (Fig.1-H) or ALARM 2 (Fig.1-G) button twice in quick succession in
normal mode.
The alarm is activated. The corresponding alarm symbol | (Fig.1-J|Fig.1-F) appears
permanently on the display.
Press again the ALARM 1 or ALARM 2 button to deactivate the alarm. The alarm symbol disappears.
When the alarm is activated, the alarm starts to ring when the set alarm time is reached. The
backlight turns on.
Press any button or flip over the alarm clock to stop the alarm.
If the alarm is not stopped manually, the ascending alarm tone automatically turns off after 3
minutes and it will be reactivated at the same set time on the following day.
When the alarm goes on, activate the snooze function by shaking it with a quick,
lateral movement.
The snooze symbol (Fig.1-L) will appear on the display.
The alarm will be interrupted for 5 minutes.
Display light
The backlight is activated by a sensor that reacts to vibrations, e.g., by lifting and setting
down the device.
Alternatively, press any button. The backlight turns on for ten seconds.
In normal mode, press or button (Fig.1-E, Fig.1-K) button to adjust the brightness in 3 steps
or switch off the backlight completely (OFF - LOW - MIDDLE - HIGH).
From 9 p.m. to 7 a.m., a permanent backlight automatically switches on at the set brightness level.
Note: If the brightness is set to “OFF”, the automatic backlighting at night is also switched off.
Night light
Press the LIGHT button (Fig.1-B) twice in quick succession in normal mode.
The night light symbol (Fig.1-C) appears on the display. The function is activated.
Flip over the alarm clock to turn on the night light. The night light faces up.
In this position you can now use the or button (Fig.1-E, Fig.1-K) to set the brightness
to 7 different levels.
To turn off the night light, flip over to the alarm clock side. The digital alarm clock faces up again.
To deactivate the night light function, press the LIGHT button twice in quick succession in normal
mode. The night light symbol disappears.
Troubleshooting
Problem: Solution:
No display on the device Charge the device via micro-USB cable (incl.)
Incorrect indication Press the RESET button (Fig.2-B) for 3 seconds
using a pin
Device makes a noise when shaken
or flipped over Not a malfunction! The device has a ball switch
that may make a slight noise when the ball rolls
around.
If your device fails to work despite these measures, contact the retailer where you purchased the product.
Specifications
Power consumption: Built-in Li-Ion rechargeable battery
Capacity / Energy: 1200 mAh
Charging power source: Micro-USB 5V DC | max. 500mA
Accessories: Charging cable (USB to Micro-USB)
Charging time: Approx. 3-4 hours
Battery runtime: Up to 200 hours (depending on the light level)
Housing dimension: 81 x 115 x 93 mm
Weight: 159 g (device only)