background image

EK50ML Battery-powered Crimping Tool

Greenlee / A Textron Company

4

IMPORTANT SAFETY INFORMATION

Inspect tool and dies before use. Replace any 

worn or  damaged parts. A damaged or improp-

erly  assembled tool can break and strike nearby 

personnel. 
Failure to observe this warning could result in severe 

injury or death.

•  Allow approximately 3 to 5 minutes of time to cool 

down as tool automatically switches off when it 

gets too hot.

•  Do not secure this tool in a vise. This tool is 

designed for hand-held operation.

•  This tool may be used in damp or wet environ-

ments; however, air-drying is recommended before 

use if the tool becomes soaked. Damage may 

result when the tool is operated prior to thorough 

drying when electrical components are soaked.

•  Use this tool for the manufacturer’s intended 

purpose only.

Failure to observe these precautions may result in 

injury or property damage.

Do not allow anything to contact the battery 

terminals.
•  Do not immerse the batteries in liquid. Liquid may 

create a short circuit and damage the battery. 

If batteries are immersed, contact your service 

center for proper handling.

•  Do not place the battery into a pocket, tool pouch, 

or tool box with conductive objects. Conductive 

objects may create a short circuit and damage the 

battery.

•  Do not place a battery on moist ground or grass. 

Moisture may create a short circuit and damage 

the battery.

Failure to observe these precautions may result in 

injury or property damage.

•  Do not store the battery at more than 122 °F 

(50 °C) or less than –4 °F (–20 °C). Damage to the 

battery can result.

•  Do not use another manufacturer’s charger. Other 

manufacturers’ chargers may overcharge and 

damage the battery.

•  Do not attempt to open the battery. It contains no 

user-serviceable parts.

Failure to observe these precautions may result in 

injury or property damage.

Do not perform any service or maintenance other 

than as described in this manual. Injury or damage 

to the tool may result.
Failure to observe this precaution may result in injury 

and property damage.

Note:  Keep all decals clean and legible, and replace 

when necessary.

www.calcert.com

[email protected]

1.800.544.2843

0

5

10

15

20

25

30

Содержание Greenlee EK50ML

















Отзывы: