background image

OPERATION AND SERVICE INFORMATION

3-22

Read all of manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notes, Cautions and Warnings

and taillight bulbs and fuses are available from a local Distributor, an
authorized Branch or the Service Parts Department.

VEHICLE WITH A DISCHARGED BATTERY

To reduce the possibility of severe
injury or death from inadvertent
motion, do not attempt to ‘jump

start’ a vehicle.

The vehicle is equipped with a starter/generator and does not idle.
When starting the engine, the starter/generator functions as a starter
and with the engine running, it functions as a generator.

With the short running times associated with this kind of vehicle, the
generator is more than adequate to maintain the battery charge level.
The generator is not designed to charge a discharged battery.

When engine starts, the clutches engage and cause vehicle to move
making ‘jump starting’ both dangerous and impractical.

If the vehicle battery has become discharged, it must be charged using
a 12 Volt charger that is rated at 10 amps or less. Read and understand
all instructions provided by the manufacturer of the charger.

TRANSPORTING VEHICLE

TOWING

This vehicle is not designed to be
towed.

It is recommended that the vehicle be moved by placing the entire vehi-
cle on a trailer, flatbed truck or other suitable transport.

NEUTRAL LOCK

To prevent the driven clutch from turning the rear wheels during service
operations, a neutral lock is located on the direction selector.

To operate:

Turn key switch to ‘OFF’ and lift seat. Pull out and rotate the neutral lock
pin handle so that the pointed portion of the handle is to the side of the
direction selector cam (Ref Fig. 22 on page 3-23). Move direction
selector towards the area between ‘F’ and ‘R’. During that motion, the
pin will snap into the hole in the direction selector mounting bracket pre-
venting any movement. When in this position, the direction selector
remains locked in the neutral position. To unlock the direction selector,
pull the neutral lock pin handle out and rotate until the pointed portion of
the handle fits into the hole in the direction selector cam. 

HAULING

To reduce the possibility of severe
injury or death while transporting
vehicle:

Secure the vehicle and contents.
Never ride on vehicle being transported.
Always remove windshield before transporting. 
Maximum speed with sun top installed is 50 mph (80 kph).

If the vehicle is to be transported at highway speeds, the sun top must
be removed and the seat bottom secured. When transporting vehicle
below highway speeds, check for tightness of hardware and cracks in
sun top at mounting points. Always remove windshield when transport-
ing. Always check that the vehicle and contents are adequately
secured before transporting. The rated capacity of the trailer or truck

!

!

!

!

!

!

Содержание EZGO Workhorse ST 350









































































Отзывы: