Texmo Industries TARO TSM Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 33

Texmo Industries TARO TSM Series Скачать руководство пользователя страница 14

Caution

The supply voltage should be within the specified voltage range.
Water temperature for operation of the pump should not exceed 33

0

C

Failure to observe the precautions given above could cause the pump to
malfunction and may lead to current leakage or electrical shock.

Warning

If you find any abnormalities like vibration, noise, smell, etc. from the pump
during trial operation, switch OFF the pump and contact the dealer where this
pump was purchased.

10. Installation procedure

Please follow the below procedure to install the openwell submersible monoblock.

The following steps are executed prior to installation

Installation

Open the filling plugs and top up, if necessary, the motor with pure drinking water

Measure the insulation resistance using a megger of 500 VDC

Ensure contact points are clean

Check the direction of rotation

Connect the measuring cable to the ground conductor

Connect the other measuring cable to every core of the motor cable in succession

Ensure that the insulation resistance, as shown on the megger, is a minimum of 20MΩ

Use prescribed pipe sizes as mentioned on the product name plate

Refer Fig. 4, shown below, for locating the OWS for operation with flooded suction.

OMOW001A

14

2020.01

«
...
12
13
14
15
16
...
»

Содержание TARO TSM Series


































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды