7
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when
changing tools and when being transported by
means other than under its own power.
Check regularly that all bolts and nuts are
tightened. Retighten if necessary.
The engine must be completely cooled before
storing indoors or covered.
If the machine unused for a period of time,
please refer to the instructions in this manual.
Maintain or replace safety and instruction
labels, as necessary.
Only use orginal spare parts or accessories. If
not orginal parts or accessories is used, the
liablility is no longer applied.
Miscellaneous
The motor is not pre-filled with oil.
Always before start check the engine oil level.
Factory-fitted control devices, such as the
handle-mounted clutch cable, must not be
removed or exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are
explosive.
Ensure that the machine is properly secured
when transported on a flatbed etc.
Waste electrical products must not be
disposed of with the household waste. This
tool should be taken to your local recycling
centre for safe treatment.
The lawnmower is manufactured according to the latest
safety requirements. These include a blade brake that
stops the motor and blade in 3 seconds when the blade
brake. Every precaution is only effective when it is
followed exactly. Use the following description when
you mount your lawnmower.
Identification of the parts
See Illustration 1
Notice: the illustrations may vary from your present
model
A. Handlebar for drive *
B. Handlebar for engine brake
C. Recoil starter
D. Oil cap
E. Spark plug
F. Rear discharge guard
G. Gasoline filling cap
H. Air Filter
I.
Primer
J.
Height adjustment
K. Grass collector
L. Side discharge guard *
M. Panel *
* may vary from your actual model.
Mounting
Unpacking:
Remove the mower from the box by pulling the machine
out form the side. The box contains:
Warning: Ensure that cables are not pinched.
Handlebar and height adjustment: Illustration 3+4
The handlebars are height adjustable. This means that
they can be adjusted so that it best fits you. Before you
install the handlebar, it may be a good idea to have
decided which height is best for you.
1. Set the lower handlebar tube to the working
angle that suits you.
2. Attach the wing nut from the inside of the side
bracket and into the lower handlebar.
3. Attach the upper handlebar on the lower.
Fasten with wing nut from the inside of the
handlebar.
4. Customize cable and secure with cable clamps
Mounting the drive cable: Illustration 5
1. Gently push the lower handlebar (B)
downward
2. Insert the drive cable (A) from the inside, into
the hole in the bracket on handlebar (B) and
lock.
Mounting the recoil-starter:
1. Pull the engine brake handlebar and hold, in
order to release the starter cord on the engine.
2. Pull gently the starter cord from the engine
(Engine brake handlebar MUST be hold)
3. Attach the starter grip on the rack of
handlebar.
4. Release the engine brake handlebar and the
starter grip.
Mounting the panel *:
1. For models with breastplate, mount it with the
2 supplied bolts and nuts.
*Note: Not all models do have breastplate
Mounting the grass collector: Illustration 6
1. Click the frame to the grass collector.
Rear discharge guard:
If you want to mow without grass collector, take off the
grass collector. Also remember to remove the mulching
plug.
Mulching plug: Illustration 7
1. Insert the mulching plug and remove side
discharge guard, if you want to mow with
mulching functionality.
NB Don’t use the grass collector
Important: Remember to remove the mulching plug,
when using the grass collector.
Side discharge guard *:
1. Lift the side guard and insert side discharge
guard. Then insert the mulching plug in rear
discharger to mow with side discharge
function. NB.
Don’t use the grass collector
*Note: Not all models have side discharge guard
