Texas Instruments TMS320x2823x Скачать руководство пользователя страница 99

Страница: 99 / 115

www.ti.com

Registers

Table 31. Action-Qualifier Output B Control Register (AQCTLB) Field Descriptions (continued)

Bits

Name

Value Description

5-4

CAU

Action when the counter equals the active CMPA register and the counter is incrementing.

Do nothing (action disabled)

Clear: force EPWMxB output low.

Set: force EPWMxB output high.

Toggle EPWMxB output: low output signal will be forced high, and a high signal will be forced low.

3-2

PRD

Action when the counter equals the period.

Note: By definition, in count up-down mode when the counter equals period the direction is defined
as 0 or counting down.

Do nothing (action disabled)

Clear: force EPWMxB output low.

Set: force EPWMxB output high.

Toggle EPWMxB output: low output signal will be forced high, and a high signal will be forced low.

1-0

ZRO

Action when counter equals zero.

Note: By definition, in count up-down mode when the counter equals 0 the direction is defined as 1
or counting up.

Do nothing (action disabled)

Clear: force EPWMxB output low.

Set: force EPWMxB output high.

Toggle EPWMxB output: low output signal will be forced high, and a high signal will be forced low.

Figure 74. Action-Qualifier Software Force Register (AQSFRC)

Reserved

R-0

RLDCSF

OTSFB

ACTSFB

OTSFA

ACTSFA

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -n = value after reset

Table 32. Action-Qualifier Software Force Register (AQSFRC) Field Descriptions

Bit

Field

Value

Description

15:8

Reserved

7:6

RLDCSF

AQCSFRC Active Register Reload From Shadow Options

Load on event counter equals zero

Load on event counter equals period

Load on event counter equals zero or counter equals period

Load immediately (the active register is directly accessed by the CPU and is not loaded from the
shadow register).

OTSFB

One-Time Software Forced Event on Output B

Writing a 0 (zero) has no effect. Always reads back a 0

This bit is auto cleared once a write to this register is complete, i.e., a forced event is initiated.)

This is a one-shot forced event. It can be overridden by another subsequent event on output B.

Initiates a single s/w forced event

SPRUG04A – October 2008 – Revised July 2009

TMS320x2833x, 2823x Enhanced Pulse Width Modulator (ePWM) Module

Submit Documentation Feedback

Содержание TMS320x2823x




















































































































Результаты поиска

Содержание TMS320x2823x

Отзывы:

Бренды по названию

Популярные бренды

Texas Instruments TMS320x2823x, Справочное руководство

Результаты поиска

Содержание TMS320x2823x

Отзывы:

Бренды по названию

Популярные бренды