manualshive.com logo in svg

Texas Instruments TMS320C3x, Руководство пользователя


Поделиться
Скачать
background image

LSH3||STI

Parallel LSH3 and STI

13-142

 

Logical right shift:

0 

→

 

src2 

→

 C

If the 

count operand is 0, no shift is performed, and the carry bit is set to 0.

The 

count operand is assumed to be a 7-bit signed integer, and the src2 and

dst1 operands are assumed to be unsigned integers. All registers are read at
the beginning and loaded at the end of the execute cycle. This means that
if one of the parallel operations (STI) reads from a register and the operation
being performed in parallel (LSH3) writes to the same register, STI accepts as
input the contents of the register before it is modified by the LSH3.

If 

src2 and dst2 point to the same location, src2 is read before dst2 is written.

Cycles

1

Status Bits

These condition flags are modified only if the destination register is R7 – R0.

LUF

Unaffected

LV

Unaffected

UF

0

N

MSB of the output

Z

1 if a 0 output is generated; 0 otherwise

V

0

C

Set to the value of the last bit shifted out; 0 for a shift 

count of 0

OVM 

Operation is affected by OVM bit value.

Mode Bit

Содержание TMS320C3x






















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C3x

D-Link ShareCenter Pulse DNS-320 Quick Install Manual preview
ShareCenter Pulse DNS-320
Бренд: D-Link Страницы: 2
D-Link DFE-680TX Quick Install Manual preview
DFE-680TX
Бренд: D-Link Страницы: 4
Paradyne 3163 Quick Reference preview
3163
Бренд: Paradyne Страницы: 16
CAME QBEMFSB2 User Manual preview
QBEMFSB2
Бренд: CAME Страницы: 19
Sangoma A400 Installation Manual preview
A400
Бренд: Sangoma Страницы: 6
LaCie d2 Network 2 Quick Install Manual preview
d2 Network 2
Бренд: LaCie Страницы: 44
LaCie LaCie Ethernet Disk Datasheet preview
LaCie Ethernet Disk
Бренд: LaCie Страницы: 2
LaCie SATA II ExpressCard 34 Datasheet preview
SATA II ExpressCard 34
Бренд: LaCie Страницы: 2
LaCie 12big Rack Fibre 8 Quick Install Manual preview
12big Rack Fibre 8
Бренд: LaCie Страницы: 9
PaloAlto Networks PA-5400 Series Quick Start Manual preview
PA-5400 Series
Бренд: PaloAlto Networks Страницы: 2
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Бренд: e-con Systems Страницы: 9
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Бренд: National Instruments Страницы: 15
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Бренд: EMS Страницы: 52
Element14 Wireless Connectivity Cape Quick Start Manual preview
Wireless Connectivity Cape
Бренд: Element14 Страницы: 2
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Бренд: Promise Technology Страницы: 26
SilverStone GD05 Manual preview
GD05
Бренд: SilverStone Страницы: 28
Harman BSS DCP-555 Installation Manual preview
BSS DCP-555
Бренд: Harman Страницы: 24
Buffalo AirStation G54 WLA2-G54 Quick Setup Manual preview
AirStation G54 WLA2-G54
Бренд: Buffalo Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды