manualshive.com logo in svg

Texas Instruments mmWaveICBoost, Руководство пользователя

Поделиться
Скачать
Texas Instruments mmWaveICBoost Скачать руководство пользователя страница 28

2.8.2.3 3.3-V Rail Options

Table 2-12. 3.3-V Rail Options

Reference Designator

Description

Image

J13

Short (1-2) : 3.3 V from FTDI LDO
Short(2-3) : 3.3 V from 40-pin LP/BP connector
Open (1-2-3) : Default

Figure 2-25. J13 Header

Note

Remove the P3 jumper when using a 3.3-V rail from the 40-pin LP/BP or FTDI LDO, and mount the
R122 resistor if it is from the 40-pin LP/BP. The current rating is limited to 1A, either from the FTDI or
40-pin LP/BP.

2.8.2.4 Miscellaneous Headers

Table 2-13

 provides the list of miscellaneous headers and usage.

Table 2-13. Miscellaneous Headers

Reference

Designator

Usage

Comments

P1

VPP 1.7-V generation for fuse chain

1-2(default) : Closed

J27

Enables/disables the load switch (U31) of 5-V supply
generation either from > 5-V or 5-V circuitry.
(1-2) indicates >5 V
(2-3) indicates 5 V

1-2 : Open
2-3 (default) :Closed

J28

Enables/disables the load switch (U32) of 5-V supply
generation either from 5-V circuitry or 40-pin LP/BP
connector.
(1-2) indicates 20-pin LP/BP
(2-3) indicates 5 V

1-2 : Open
2-3 (default) :Closed

J16

LP/BP spare header

Onboard 10-pin header provides external user control for
configuring the LP/BP pins partially.

J18

DMM trace header 1

Onboard 16-pin header provides external user control for
JTAG trace signals.

J20

DMM trace header 2

Onboard 16-pin header provides external user control for
JTAG trace signals.

MMWAVEICBOOST

www.ti.com

28

mmWaveICBoost and Antenna Module

SWRU546D – OCTOBER 2018 – REVISED NOVEMBER 2020

Submit Document Feedback

Copyright © 2020 Texas Instruments Incorporated

Содержание mmWaveICBoost



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды