Texas Instruments mmWaveICBoost Скачать руководство пользователя страница 19

Страница: 19 / 82

2.6 Power Connections

The board is powered by 5-V power jack (2-A current limit) shown in

Figure 2-13

Figure 2-13. Power Connector

Table 2-3

provides the jumper information for usage of board power input.

Note

TI recommends using an external power supply that complies with applicable regional safety
standards, such as UL, CSA, VDE, CCC, PSE, and more. The length of the power cable should be <
3 m.

Table 2-3. Board Power

Reference

Designator

Description

Image

Short(Default) : Input voltage is 5 V and short
R116.
Open : Input voltage is more than 5 V and
remove R116.

Figure 2-14. P3 Header

Short : Input voltage is more than 5 V and
remove R116.
Open : Input voltage is 5 V.

Figure 2-15. P7 Header

J27

Short (1-2): Input voltage is more than 5 V.
Open(2-3): Input voltage is 5V(Default)

Figure 2-16. J27 Header

2.7 Connectors

There are several types of connectors used in the MMWAVEICBOOST board, which are mentioned below.

www.ti.com

MMWAVEICBOOST

SWRU546D – OCTOBER 2018 – REVISED NOVEMBER 2020

Submit Document Feedback

mmWaveICBoost and Antenna Module

Содержание mmWaveICBoost



















































































Результаты поиска

Содержание mmWaveICBoost

Отзывы:

Похожие инструкции для mmWaveICBoost

Бренды по названию

Популярные бренды

Texas Instruments mmWaveICBoost, Руководство пользователя

Результаты поиска

Содержание mmWaveICBoost

Отзывы:

Похожие инструкции для mmWaveICBoost

Бренды по названию

Популярные бренды