Texas Instruments Jacinto 7 DRA829 Скачать руководство пользователя страница 1

Страница: 1 / 55

User’s Guide

Optimized Dual TPS6594-Q1 PMIC User Guide for
Jacinto

™

7 DRA829 or TDA4VM Automotive PDN-0C

ABSTRACT

This user’s guide can be used as a guide for integrating the TPS6594-Q1 power management integrated circuit
(PMIC) into a system powering the DRA829 or TDA4VM processor.

Table of Contents

1 Introduction

.............................................................................................................................................................................

2 Device Versions

......................................................................................................................................................................

3 Processor Connections

..........................................................................................................................................................

3.1 Power Mapping..................................................................................................................................................................

3.2 Control Mapping.................................................................................................................................................................

4 Supporting Functional Safety Systems

..............................................................................................................................

4.1 Achieving ASIL-B System Requirements.........................................................................................................................

4.2 Achieving up to ASIL-D System Requirements................................................................................................................

5 Static NVM Settings

..............................................................................................................................................................

5.1 Application-Based Configuration Settings........................................................................................................................

5.2 Device Identification Settings...........................................................................................................................................

5.3 BUCK Settings.................................................................................................................................................................

5.4 LDO Settings....................................................................................................................................................................

5.5 VCCA Settings.................................................................................................................................................................

5.6 GPIO Settings..................................................................................................................................................................

5.7 Finite State Machine (FSM) Settings...............................................................................................................................

5.8 Interrupt Settings..............................................................................................................................................................

5.9 POWERGOOD Settings...................................................................................................................................................

5.10 Miscellaneous Settings..................................................................................................................................................

5.11 Interface Settings............................................................................................................................................................

5.12 Multi-Device Settings.....................................................................................................................................................

5.13 Watchdog Settings.........................................................................................................................................................

6 Pre-Configurable Finite State Machine (PFSM) Settings

..................................................................................................

6.1 Configured States............................................................................................................................................................

6.2 PFSM Triggers.................................................................................................................................................................

6.3 Power Sequences............................................................................................................................................................

7 Application Examples

..........................................................................................................................................................

7.1 Moving Between States; ACTIVE, MCU ONLY, and RETENTION..................................................................................

7.2 Entering and Exiting Standby...........................................................................................................................................

7.3 Entering and Existing LP_STANDBY...............................................................................................................................

7.4 Runtime Customization....................................................................................................................................................

8 References

............................................................................................................................................................................

Trademarks

Jacinto

™

are trademarks of Texas Instruments.

All trademarks are the property of their respective owners.

www.ti.com

Table of Contents

SLVUC99 – JANUARY 2022

Submit Document Feedback

Optimized Dual TPS6594-Q1 PMIC User Guide for Jacinto

™

7 DRA829 or

TDA4VM Automotive PDN-0C

Содержание Jacinto 7 DRA829
























































Результаты поиска

Содержание Jacinto 7 DRA829

Отзывы:

Похожие инструкции для Jacinto 7 DRA829

Бренды по названию

Популярные бренды

Texas Instruments Jacinto 7 DRA829, Руководство пользователя

Результаты поиска

Содержание Jacinto 7 DRA829

Отзывы:

Похожие инструкции для Jacinto 7 DRA829

Бренды по названию

Популярные бренды