Texas Instruments ADS1 7 EVM-PDK Series Скачать руководство пользователя страница 4

Страница: 4 / 31

Quick Start

www.ti.com

Quick Start

This section provides a QuickStart guide to quickly begin evaluating the ADS1x7xEVM with ADCPro.

2.1

Default Jumper/Switch Configuration

Figure 1

shows the jumpers found on the EVM and the respective factory default conditions for each.

Figure 1. ADS1x7xEVM Default Jumper Locations

Table 2

lists the jumpers and switches and the factory default conditions.

Table 2. Default Jumper/Switch Configuration

Switch

Default Position

Switch Description

All OFF (Down)

Powerdown channel DIP switches (Hardware control)

Mode, Format, and CLKDIV DIP switches(Hardware

All OFF (Down)

control)

INT (Right)

On-board Voltage Reference Selected

Channel 4 header connected to converter (not

Header connected to converter (Left)

buffered)

Channel 3 header connected to converter (not

Header connected to converter (Left)

buffered)

FS (Down)

FS serial interface format

Channel 2 header connected to converter (not

Header connected to converter (Left)

buffered)

Channel 1 header connected to converter (not

Header connected to converter (Left)

buffered)

ADS1x7xEVM-PDK

SBAU197

–

February 2012

Submit Documentation Feedback

2012, Texas Instruments Incorporated

Содержание ADS1 7 EVM-PDK Series
































Результаты поиска

Содержание ADS1 7 EVM-PDK Series

Отзывы:

Похожие инструкции для ADS1 7 EVM-PDK Series

Бренды по названию

Популярные бренды

Texas Instruments ADS1 7 EVM-PDK Series, Руководство пользователя

Результаты поиска

Содержание ADS1 7 EVM-PDK Series

Отзывы:

Похожие инструкции для ADS1 7 EVM-PDK Series

Бренды по названию

Популярные бренды