Texas Equipment CHX2000, Руководство пользователя

Страница: 12 / 24

12
6. Chain lubrication
The chainsaw is equipped with an automatic
lubrication system, which ensures the chain is always
lubricated optimally. However, the system depends
on chain oil in oil tank and regular cleaning.
The chainsaw is not supplied filled with oil. It is
essential to fill with oil before use. Never
operate the chainsaw without chain oil or at an
empty oil tank level, as this will result in
extensive damage to the product.
Chain life and cutting capacity depend on optimum
lubrication. Therefore, the chain is automatically oiled
during operation via oil outlet.
Check the automatic operation of the chain lubrication
by pointing the tip of the switched –on saw towards a
piece of paper laying on the ground, if a patch of oil
appears and becomes larger, then the automatic oil
function is working. If there are no traces of oil even
though the oil tank is full. Then the automatic oil
function is not working. If the automatic oil function is
not working. Remove the chain bar and clean out the oil
ways of the chainsaw and chain bar, on reassemble if
the chainsaw is still not working take it to a autorised if
the chainsaw is still not working take it to an autorised
service centre.
Use correct chain oil to avoid damage to the chainsaw.
Never use recycled/old oil.
Use of non-approved oil will invalidate the warranty.
Check oil level prior to starting and regularly during
operation Fig. 8. Refill oil when oil level is low.
7. Use
Before use, make sure that the battery is fitted properly
with the battery lock in place. (9+10)
Remove the bar cover and hold the electric saw by its
grip with hands. To start the chainsaw, press the lock-
off button (11) on the trigger switch. To stop the chain
saw release the trigger switch. Warning: hold the
electric chain saw with hands until the chain is
completely still.
Adjust speed.
When the chain saw is normally started, the indicator
light (15) is green, and the chain saw is running at low
speed. Press the speed control button (11) again, the
indicator light turns red, and the chain saw is running at
high speed. Remarks: The working state of the
chainsaw can be switched freely by pressing the speed
control button. The indicator light shows green for low
speed, and the indicator light shows red for high speed.
8. Kickback safety devices
This saw has a low-kickback chain and reduced
kickback guide bar.
Both items reduce the chance of kickback. Kickback
can still occur with this saw.
The following steps will reduce the risk of kickback.
•
Keep solid footing and balance at all times.
•
Do not let guide bar nose touch anything when
chain is moving.
•
Never try cutting through two logs at same time.
Only cut one log at a time.
•
Do not bury guide bar nose or try plunge cut
(boring into wood using guide bar nose).
•
Watch for shifting of wood or other forces that may
pinch chain.
•
Use extreme caution when re-entering a previous
cut.
•
Use low-kickback chain and guide bar supplied
with this chainsaw.
•
Never use dull or loose chain. Keep chain sharp
with proper tension.
10. Clothing
When using the machine, wear tight-fitting work clothes,
strong working gloves, hearing protectors, eye
protection, safety boots with non-skid soles and
protective trousers.
11. Tips and advices
Use the chainsaw only with secure footing.
The chain must be running at full speed before it makes
contact with the wood.
Do not attempt to saw areas which are difficult to reach,
or on a ladder.
12. Maintenance
Before any service and maintenance is done,
the power must be disconnected, it means the
battery removed from the tool.
•
Remove the battery before you clean and store the
machine.
•
For obtaining the best cutting results the chain and
guide bar must be cleaned and oiled regularly.
Remove dirt with a brush and oil lightly.
•
Use biodegradable oil.
•
Clean the housing and other parts with a mild
cleanser and a moist cloth. Never use aggressive
cleansers or solvents.
•
Prevent water from getting into the machine.
•
Use the guide bar cover when the machine is
stored.
Lubrication hole . Remove the guide bar and check
that the lubrication hole is not blocked with sawdust
or dirt. Lubricate with oil/grease.’
Guide bar . Clean the nose wheel and chain groove
of any dirt. If required, turn the guide bar over to