Texas Equipment CHX2000, Руководство пользователя

Страница: 11 / 24

11
Setting the chain saw tension
Before adjusting chain, make sure guide bar nuts are
only finger tight. Also make sure adjusting block is in
oval adjusting hole on guide bar. turn adjusting screw
(Fig. 6) clockwise until all slack is out of chain. Note:
there should be no gap between side likes of chain ad
bottom of guide bar. wearing protective gloves, move
chain around guide bar, chain should move freely. If
chain does no move freely. Loosen chain by turning
adjusting screw counterclockwise. After chain tension is
correct , tighten guide bar nuts firmly. If not, guide bar
will move and loosen chain tension. This will increase
the risk of kickback, this can also damage saw, Note: a
new chain will stretch, check new chain after first few
minutes of operation. Allow chain to cool down.
Readjust chain tension.
WARNING! Do not over
tension the chain as this will lead to excessive wear and
will reduce the life of bar and chain. Over tensioning
also reduce the amount of cuts you should get.
Oil filling
Note: the chain saw is shipped without oil in it, the chain
saw must never be used without oil or with an oil level
that is below the indicator. Warning , always ensure that
the chainsaw is switched off and the plug is removed
from the power point before making any adjustments.
1. Remove oil cap. (Fig. 7)
2. Fill oil tank with chain Lubricating oil.
3. check the oil level periodically, through the oil level
indicator(fig.8)
4. wipe off excess oil.
Note: it is normal for oil to seep when saw is not in use.
Empty oil tank after each use to prevent seepage.
4. Battery
Not included for solo machines*
To get the best performance of the chainsaw, it is
recommended to use the 4.0 Ah battery.
Warning: Do not try to disassemble, short circuit or put
it to extreme heat or fire, as it can cause serious inquiry
and permanent damage to the battery!
Battery pack is not fully charged when delivered.
Charging
•
Only use the original charger with
art. no. 90063242 or 90063241.
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights Battery Pack
All LEDs are lit Fully charged (75-100%).
LED 1, LED 2, LED 3
are lit.
The battery pack is
50%-75% charged
LED 1, LED 2
are lit.
The battery pack is
25%-50% charged.
LED 1 are lit
The battery pack is
0%-25% charged
LED 1 flashes
The battery pack is empty.
Charge the battery.
Note: The indicator lighs is only indicative indications,
and is not accurate power indications.
Important: To protect the battery from total
discharge, the machine will stop, when the battery is
nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can
continue.
5. Charger
A full charge takes around 60 min for 2.0 Ah batteri and
120 min for 4.0 Ah battery.
•
Only use the original charger*
•
Do not try to charge other type of batteries in the
charger, other than the original batteries with art.
no. 90063245 (2.0 Ah) or 90063246 (4.0 Ah).
•
Keep the charger in a dry and warm environment
(10-25 degrees C) and only use it indoor. It should
be connected to a normal 230V AC socket.
•
Before the battery is being used the first time, it is
recommended to charge it fully.
•
The surface of the battery can become warm
during charging. This is normal.
•
Do not cover battery or charger during charging.
Allow free ventilation of air.
Insert the battery into the slots of the charger and
slide it into place until it locks.
There are 4 lights on the charger indicating the status
and state of charge of the battery.
Status
Charging
Fully charged
Evaluate
Defective
Important:
The charger will stop, when the battery is
full. However, it is not recommended to leave the
battery in charger for more than 24 hours.
It is recommended to drain the battery completely and
fully charge it whenever possible, as it can increase
the health of the battery. But partial charge will not
damage the battery.
To remove the battery from the charger, hold the
button down and pull the battery out.
Before winter storage, the battery should be fully
charged and kept warm at 10-20 degrees C. Charge it
every 3 months. Make sure to keep ventilation holes
clean and free from dirt.
Store the charger indoor between 5-25 degrees C.