SPECIFICATIONS
LG 226
RF Output
Frequency Range:
30 MHz to 950 MHz
Frequency Resolution:
50 kHz
Frequency Accuracy:
10 ppm
Frequency Switching Time:
Within 100 ms
Frequency Setting
Channel
Mode:
Setting with a built-in channel table
Frequency
Mode:
Setting an arbitrary frequency
Output Impedance:
75
Ω
Output Connector:
BNC
Output Level Range:
-80 to 0 dBm (0 dBm max.)
Level Resolution:
1
dB
Output Level Accuracy:
±2 dB (0 to -9 dBm)
±3 dB (-10 to -80 dBm)
Spurious:
Within -30 dBc (Harmonics)
Within
-40
dBc
(Non-Harmonics)
Video Signal
Modulation System:
Amplitude modulation of the VSB
(vestigial sideband) system according
to a broadcast system
Modulation
At the time of built-in channel table setting:
87.5
%±3
%
(Negative
modulation)
97.0
%±3
%
(Positive
modulation)
At the time of arbitrary setting:
0 to 100 % (in 0.5 % steps)
Modulation Frequency Band
At the time of built-in channel table setting:
4.2
MHz/5.0
MHz/6.0
MHz
(Depends
on a broadcast system)
At the time of arbitrary setting:
4.2
MHz/5.0
MHz/6.0
MHz
Modulation Frequency Flatness:
±1 dB
Input Impedance:
75
Ω
Input Connector:
BNC
Reference Input Level:
1 Vp-p
Spectrum Polarity:
Positive (upper sound wave)
Built-in Pattern:
Full-field Color Bar (NTSC/PAL)
Line sweep (at 100 % modulation: 4.2
MHz) (NTSC/PAL)
Sound Signal
Carrier Frequency
At the time of built-in channel table setting:
4.5
MHz/5.5
MHz/6.0
MHz/6.5
MHz
(Depends on a broadcast system)
At the time of arbitrary setting:
4.5 to 6.5 MHz (in 0.5 MHz steps)
Video Sound Ratio
At the time of built-in channel table setting:
-6 dB/-7 dB/-10 dB (Depends on a
broadcast system)
At the time of arbitrary setting:
-30 to 0 dB (in 1 dB steps)
Modulation Types:
FM/AM (L System) (Depends on a
broadcast system at the time of built-
in channel table setting)
Frequency Deviation
At the time of a built-in channel table Setting:
15 kHz/30 kHz(equivalent to 60 %
of the maximum deviation for each
broadcasting system)
At the time of an arbitrary setting:
0 to 100 kHz (in 1 kHz steps)
Modulation (AM)
At the time of built-in channel table Setting:
60 %
At the time of arbitrary setting:
0 to 60 % (in 1 % steps)
Pre-Emphasis
At the time of built-in channel table setting:
75 μs/50 μs (Depends on a broadcast
system)
At the time of arbitrary setting:
75
μs/50
μs/OFF
Modulation Frequency Response:
40 Hz to 100 kHz
Modulation Frequency Flatness:
±1 dB
Reference Input Level:
0 dBm (0.775 Vrms)
Input Impedance:
600
Ω
Input Connector:
BNC
Built-in Sound Signal:
Sine wave 400 Hz/1 kHz
* The modulation system cannot be selected at the time of
channel mode.
Preset
Function:
Up to 100 sets of panel settings can
be stored and recalled.
GPIB
Function:
Enables the key operations of the
front panel except a power switch.
Connector:
24-pin rectangular connector
57LE-20240-7700D35G
(DDK)
or
equivalent
Corresponding Standard:
ANSI/IEEE Std 488.1-1987
REMOTE
Function:
Enables the INC, DEC, and RESET
operations of the preset memory.
Connector:
14-pin rectangular connector
57LE-4014-7700
(DDK)
or
equivalent
Input Level:
TTL
RS232C
Function:
Controls the Video signal generator
LT 450, Selects the INC, DEC, or RE-
SET/video format which are related to
the PRESET-MEMORY.
Connector:
9-pin D-Sub (M)
Signal Format:
Bidirectional serial data
Environmental Conditions
Operating Temperature:
0 to 40 °C
Operating Humidity:
≤85 %RH (without condensation)
Operating Environment:
Indoor use
Operating Altitude:
Up to 2,000 m
Overvoltage Category:
II
Pollution Degree:
2
Power Requirements
Voltage:
AC90 to 250 V
Power Frequency:
50/60
Hz
Power Consumption:
35 W max.
Dimensions
426(W) X 88(H) X 400(D) mm
(excluding
projections)
Weight
5.6
kg
Accessories
AC
power
cord
................................. 1
Instruction
manual
........................... 1
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
FAX 781.665.0780 - TestEquipmentDepot.com
