Teryair DP 25 ALS Скачать руководство пользователя страница 10

Страница: 10 / 33

FF-MM-326-REV -01

Page 10

Operation and Maintenance Guide SDP 25 Metal Series

e. Wrap electrical tape around each leg of the

needle nose pliers (heat shrink may also be

used) . This is done to prevent damaging the

inside portion of the new seals.

f. With a new seal in hand, place the two legs of

the nose pliers inside the seal ring. Open the

pliers as wide as the seal diameter will allow,

then two fingers pull down on the top por-

tion of the seal to form kidney bean shape.

(Refer Fig. A)

g. Lightly clamp the pliers together to hold the

seal into the kidney shape. Be sure to pull the

seal into as tight of a kidney shape as possi-

ble, this will allow the seal to travel down the

bushing bore easier. (Refer Fig. B)

h. With the seal clamped in the pliers, insert the

seal into the bushing bore and position the

bottom of the seal into the correct groove.

Once the bottom of the seal is seated in the

groove, release the clamp pressure on the pli-

ers. This will allow the seal to partially snap

back to its original shape.

i. After the pliers are removed, you will notice a

slight bump in the seal shape. Before the seal

can be properly re-sized, the bump in the seal

should be removed as much as possible. This

can be done with either the Phillips screw

driver or your finger, apply light pressure to

the peak of the bump. This pressure will cause

the bump to be almost completely eliminat-

ed.

j. Lubricate the edge of the shaft with specified

lubricant.

k. Slowly insert the shaft with rotating motion.

This will complete the re-sizing of the seals.

l. Perform these steps for the remaining seals.

3. Replacement Of Secondary Shaft

Assembly

a. For removing the secondary shaft assembly

from center piece assembly, first follow the

steps a, b, c, d from the diaphragm replace-

ment and remove the outer chamber (4).

b. Repeat the same procedure to remove the

other side also.

c. Remove the Circlips (17) from Shaft housing

assembly housing (A) & take out the Sleeve

(16) by pushing it from the shaft housing

assembly (A).

d. Now remove the end O-rings (38A) from

both ends of secondary shaft assembly

(38).

e. Now if you see there is a center drill mark on

one side of the secondary shaft assembly (38).

Pull the secondary shaft assembly (38) from

this side only.

f. During assembly make sure to push the

secondary shaft assembly (38) from the plain

side only into the sleeve (16).

Содержание DP 25 ALS


































Результаты поиска

Содержание DP 25 ALS

Отзывы:

Бренды по названию

Популярные бренды

Teryair DP 25 ALS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DP 25 ALS

Отзывы:

Бренды по названию

Популярные бренды