background image

MOUNTING THE CHAIN SAFETY GUIDE

Read these instructions carefully before installing and

using the chain safety guide.

Children can be strangled if this safety device is not

installed correctly. Use of safety device helps reduce

the risk of strangulation but cannot be considered

entirely fool proof.
A

 With the chain safety guide on the chain, mark a

suitable mounting position for the chain safety guide

at a point where it keeps the chain taut. 

NOTE: The

safety device shall not be installed less than 1.5m 

from the floor. 

It is essential that the chain safety guide 

shall be installed at the maximum distance possible from 

the control mechanism to prevent the looped chain 

becoming slack.

B

 Use appropriate fixings to mount the chain safety

guide, depending on the surface to which the device

is being fitted.

Children can strangle if this safety device is not

installed correctly. Always use this device to keep

cords or chains out of reach of children.

STEP 15

CONVERTING TO LEFT HAND DRAW

UNTRIMMED TRACK
A

 Unscrew, slide and remove the end cover and chain

pulley.

B

 Slide the end cover and chain pulley into the opposite

ends of the rail from previous. Tighten screws to secure.

STEP 16

CONVERTING TO LEFT HAND DRAW

TRIMMED TRACK
A

 Unscrew, slide and remove the end cover and chain

pulley.

B

 Slide the inner bar at the end where the chain pulley

will be placed into the rail so it is at least 2cm from the

rail end for 120 - 150cm, and 3cm for 150 - 210cm

rails.

C

 Rotate the bar so that the grub screws at the side of

the cord guides are accessible. Loosen both the cord

guide screws and grub screws. Reposition so that they

align with the corded positions on the blind.

Secure the cord guide screws and grub screws.

D

 Slide the end cover and chain pulley into the opposit

ends of the rail from previous. Tighten screws to secure.

STEP 17

Use Cassette Roman Blind Kit

Need some more help?

Talk to our customer service experts

on 

01782 566 666

fabrics

To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords may become wrapped around 

a child’s neck. Move beds, cots and furniture away from window covering cords.
Do not tie cords together. Make sure cords do not twist and create a loop. Cut the cord to suitable length to ensure it can be 

wound around the cleat several times when your roman blind is both open and closed.
Children can strangle if the cleat device is not installed. Always use this device to keep cords out of reach of children.

WARNING

Young children can be strangled by loops in pull cords, chains, tapes and inner cords

that operate the product.

Содержание Cassette Roman Blind Kit






Отзывы: