TERMA KTX 1 Скачать руководство пользователя страница 10

KTX 3

Control Panel 

Display Panel 

MANUAL MODE 

Heating element heats the radiator that it is installed in and, at the same time, controls 

its temperature. 

For temperature regulation please use buttons   and   . LCD display panel shows current 

temperature measured inside the radiator. After settings have been modified, display 

panel will flash showing the newly set temperature for a few seconds and will go back to 

displaying current temperature. Heating indicator   will come up on the display panel if 

the newly set temperature is higher than the current one. 

In order to view the set temperature, please press any of the parameters regulation 

buttons once.

Construction of the device as well as physical characteristics of the heating agent inside 

the radiator influence the way in which the heat is distributed – the temperature of the 

bottom pipes of the radiator (especially the two located at the very bottom of the radia-

tor) may be lower than the temperature of the remaining parts of the radiator – this  

is a normal phenomenon.

Turning the device on does not mean that it uses the same maximum power for the whole 

time it is on. On turning the device on, it operates with the nominal power for a short 

period of time in order to heat up the radiator to the set temperature. After that it turns 

itself on and off periodically, using only as much energy as it is required to maintain the 

set temperature of the radiator for current external conditions.

ANTI-FREEZE FUNCTION

When the device is off and temperature around the temperature sensor drops down 

below 6°C, the device will switch on automatically. This is to prevent the heating agent 

inside the radiator from freezing. Display panel will show AF code.

DRYER MODE

Dryer mode allows to turn the device on for a certain length of time, ie. in order dry  

a towel. 

After the set length of time the device will go back to the setting from before 

the dryer mode has been activated. 

You switch the dryer on by quickly pressing   once – 

Dryer default parameters are: 

temperature of 50°C, drying time: 2 hours.

 Any subsequent quick pressing of the button 

will prolong the drying time by 0.5 hour up to 4 hours. Having reached 

4 hours, the clock goes back to the start on pressing the   button again.

Small numeric field displays exact drying time left, 

while the big one shows the same time rounded 

to a full hour.

If the device had been off before the dryer was 

activated, it will turn off automatically after the 

dryer mode is finished.

In order to interrupt the dryer mode at any time, please press  .

CLOCK 

Current time (hh:mm) is displayed both when the device is on and when it is off with an 

exception of the dryer activation time or when the device is being programmed.

time settings  

(clock/dryer/timer) –

– on/off button

– parameters regulation 

Содержание KTX 1

















Отзывы: