Teracue DEC-200 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 62

Teracue DEC-200 Скачать руководство пользователя страница 60

DEC-200™ H.264 and MPEG-2 Decoder
User Guide V2.6

60

6. Known Issues



The DEC-200™ firmware versions till version 0.1.17 do not support the ‘Factory-Reset’
feature. So if your DEC-200™ has a lower firmware version than 0.1.18 and if you change the
IP-address of your decoder, please make a note of the new decoder IP-address and save this
note.



Concerning all firmware versions from 0.1.8 till 0.1.16: For unicast reception you must enter in
the ‘IP address’ field of the ‘DECODER/SOURCE’ webpage the IP-address of the DEC-200™,
e. g. 172.16.20.200. See Figure 43.

Figure 43: Unicast Reception (For Firmware Versions 0.1.8 - 0.1.16)



All  DEC-200™  firmware  versions  since  version  0.1.19  are  for  the  DEC-200™  Hardware
Revision  2.  If  a  DEC-200™  Hardware  Revision  1  will  be  updated  with  a  firmware  version
0.1.19  or  higher,  the  DEC-200™  Hardware  Revision  1  supports  still  only  the  features  till
firmware version 0.1.18.



If the DEC-200™ is set to DHCP, a downgrade to a lower DEC-200™ Firmware than 0.1.24
may not made, because in this case no network address will be assigned.



A  range  of  DEC-200™  decoders  have  the  +3.3  V  at  Pin  24  which  is  protected  with  a  1k
resistor. The listed serial numbers below specifies the DEC-200™ decoders with this resistor.
At these  decoders,  the  +3.3  V can not be  used  as  a  supply  voltage. At  all  other  DEC-200™
decoders,  which  are  not  listed  here,  the  auxiliary  supply  can  be  used  as  a  fused  supply
voltage with max. 500mA current.

S/N: 00:50:C2:39:71 - 00:50:C2:39:7E
S/N: 256/0839/100 - 256/0839/157
S/N: 256/0839/159 - 256/0839/180
S/N: 256/0839/185 - 256/0839/194
S/N: 2MK/0912/251 - 2MK/0912/287
S/N: 2MK/0921/301 - 2MK/0921/314
S/N: 2MK/0921/316 - 2MK/0921/356
S/N: 2MK/0921/449
S/N: 2MK/0921/451 - 2MK/0921/459
S/N: 2MK/0921/461



The  DEC-200™  firmware  version  1.30  or  higher  does  support  not  anymore  the  DEC-200™
Hardware  Revision  1.  So,  if  you  have  a  DEC-200™  Hardware  Revision  1  blade,  it  is  very
important that you do not update your DEC-200™ with the firmware version 1.30 or higher.

«
...
58
59
60
61
62
»

Содержание DEC-200































































Отзывы:

Нет отзывов