tepro Danbury, Руководство по эксплуатации

Страница: 16 / 20

16
t
Setting up the pizza oven
Attention Risk of damage!
During use, the screws can loosen slowly.
– Check that all screws are tightened before use. If necessary,
tighten all screws to guarantee stability.
– Place the pizza oven outdoors on a level, heat-resistant, solid
surface.
– When using the pizza oven, the floor and wall surfaces can
occasionally be contaminated, e.g. from splashes of fat. Make
sure that the subsurface is adequately protected against such
contamination.
before baking
• Wash off any coarse production residues with warm water,
avoiding the use of detergents or detergents.
Pre-firing
• Before baking for the first time, heat up the pizza oven for
a min. 15 minutes with a closed lid and high flame without
food. The heat cleans the internal parts and burns away the
finishing residues of coloured parts. In the process, odours
and some smoke may develop. However, this is harmless and
only lasts a short time. Ensure sufficient ventilation.
Pre-heating
• It is recommended to preheat the pizza oven for about 10-15
minutes before each use.
Pizza stone
• DO NOT use the stone over an open flame.
• Avoid extreme temperature fluctuations in the stone.
DO NOT put frozen food on a hot stone.
• The stone is fragile and can break if hit or dropped.
• The stone is very hot during use and will stay hot for a long
time after use.
• DO NOT cool a hot stone with water.
Operation
Danger Risk of burning!
The pizza oven, contained pellets and baking items
get very hot during use so that contact with them can
cause serious burns.
– Keep away from hot parts as any contact can cause severe
burns.
– Always wear oven or BBQ gloves when baking. (Glove Cate-
gory II with regard to heat protection, e.g. DIN-EN 407. Glove
must match the PSA regulation.)
– Use long-handled utensils with heat-resistant handles only.
– Do not wear any clothing with wide sleeves.
1. Open the vent chimney (01)
6
Operation guideline
3. Add pellets (about 380 grams (0.8lb), reach to about 2/3 of the pellet collector (02).
4. Use the ignition gun to light the pellets directly.
1. Open the chimney (01) lid.
2. Close the door (08).
2. Close the door (08).
6
Operation guideline
3. Add pellets (about 380 grams (0.8lb), reach to about 2/3 of the pellet collector (02).
4. Use the ignition gun to light the pellets directly.
1. Open the chimney (01) lid.
2. Close the door (08).
Step 6
Assemble the pizza peel (9).
5
3. Connect Gas hose & Regulator (3) to Pizza Oven (2).
4. Assemble the pizza shovel.
WARNING
• Please always keep the gas bottle in upright position.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The minimum distance for the appliance and the 20lb gas tank is 40 inches apart.
CONNECTING THE LIQUID PROPANE GAS CYLINDER
1. The cylinder valve should be in OFF position.
2. Make sure the burner valve is in OFF position.
3. Inspect the valve connections, port and regulator assembly. Remove debris and inspect the hose for damage.
4. When connecting the regulator assembly to the valve, use your hand to tighten the nut clockwise until it tops.
5. Use of a wrench could damage the quick coupling nut and result in a hazardous situation.
6. Open the cylinder valve fully by turning the valve counterclockwise.
7. Before lighting the oven, use a soap and water solution to check all connections for leaks.
8. If a leak is found, turn the cylinder valve OFF, and do not use the oven until local liquid propane dealer make repairs.
CLOSE THE LIQUID PROPANE GAS CYLINDER
1.Turn the oven burner valve OFF and make sure the oven is cool.
2. Turn the liquid propane cylinder valve OFF by turning clockwise until it stops.
3. Detach the regulator assembly from the cylinder valve by turning the quick coupling nut counterclockwise.
4. Place dust cap for cylinder valve outlet whenever the cylinder is not in use.
LEAK TESTING
GENERAL
Although the gas connections of the appliance are leak tested prior packing and shipment, a complete test must be performed at the installation site
and before each use.Check all the gas connections for leak testing using the procedure listed below. If the smell of gas is detected at any time, you
should immediately stop using and check the entire system for leaks.
BEFORE TESTING
Make sure all packing material has been removed from the appliance.
Make a solution of one part liquid detergent and one part water. You will need a spray bottle, brush or rag to apply the solution to the fittings.
A
B
C
D
(09)
P21098_TEPRO_1173_PelletPizzaofen_Danbury_DE_GB_210831.indd 16 31/8/2021 12:36 PM