Tense RGM-12S Скачать руководство пользователя

Страница: 19 / 26

Settings

Low Compensation

Adjusting the Low Compensation Value:

In case the Cosine value

stays under the Low Compensation Value for 3 minutes although the

device activates all steps, it enters an undercompensation error, the

alarm relay is energized, the LOW led flashes while the alarm and

SETTINGS leds are constantly lit. When the cosine value returns to the

normal level for 10 seconds, the device disables the

undercompensation error, the alarm relay is deactivated, the alarm

and LOW led turn off, the cosine led turns on.
After entering the settings menu, the first parameter displayed on the

screen is Pr1: Current Transformer Ratio. Press the DOWN button to access

Pr9: Low Compensation Time p arameter. To see the parameter value, press

the "SET" button and see that the led of the Pr9 parameter is blinking.
When the parameter led is blinking, you can change the value of the

parameter by using the DOWN and UP buttons. After changing the value

of the parameter, press the SET button to save and press the ESC button

to return to the previous menu without saving.
When the changed parameter value is saved by pressing the SET button, the device

returns to the previous menu, the parameter value is displayed on the screen and the

parameter led does not blink, it lights up steadily. When the changed parameter value is

saved by pressing the SET button, the device returns to the previous menu, the parameter

value is displayed on the screen and the parameter led does not blink, it lights up steadily.

8 8 8 8

- 9 8 5

. .

8 8 8 8

- 9 8 5

. . .

8 8 8 8

0 0 1 0

. .

SET

(2sec.)

8 8 8 8

0 0 1 5

. .

Settings

Harmonic Voltage

Adjusting the THD-V Value:

If the Total Harmonic Distortion Voltage

(THD-V) value stays above the THD-V Set value for 15 seconds, the

device enters a THD-V error, it stops compensation, the alarm relay

isenergized (it deacitivates all steps), the alarm led turns on and the

THDV led (Pr10: THD -V Set) flashes. When the THD-V value stays

below 3% of the THD-V set value for 15 seconds, the device disables

the THD-V error, the alarm relay is deenergized, the alarm and THD-V

led (Pr10: THD-V Set) turns off, the Cosine led turns on. The device

restarts compensation.
After entering the settings menu, the first parameter displayed on

the screen is Pr1: Current Transformer Ratio. Press the DOWN button

to access Pr10: TDH-V Set parameter. To see the parameter value,

press the "SET" button and see that the led of the Pr10 parameter is

blinking.
When the parameter led is blinking, you can change the value of the

parameter by using the DOWN and UP buttons. After changing the

value of the parameter, press the SET button to save and press the

ESC button to return to the previous menu without saving.
When the changed parameter value is saved by pressing the SET

button, the device returns to the previous menu, the parameter value

is displayed on the screen and the parameter led does not blink, it

lights up steadily.

8 8 8 8

- 9 8 5

. .

8 8 8 8

- 9 8 5

. . .

8 8 8 8

1 0

. . .

SET

(2sec.)

8 8 8 8

1 5

. . .

Example:

Let Cosine set: 0.940, Cosine tolerance: 10 and low compensation: 10. If the cosine value stays

under 0.920 for 3 minutes even though it activates all steps, this error occurs. If the cosine value goes

above 0.930 for 10 seconds after the error, the error situation will disappear.
NOTE: This feature is disabled in manual mode.

DOWN

Settings

Harmonic Current

Adjusting the THD-I Value:

If the Total Harmonic Distortion Current

(THD-I) value stays above the THD-I Set value for 120 seconds, the

device enters a THD-I error, it stops compensation, the alarm relay

isenergized (it deacitivates all steps), the alarm led turns on and the

THDI led (Pr11: THD-I Set) flashes. When the THD-I value stays below

5% of the THD-I set value for 60 seconds, the device disables the THD-

I error, the alarm relay is deenergized, the alarm and THD-I led (Pr11:

THD-I Set) turns off, the Cosine led turns on. The device restarts

compensation.
After entering the settings menu, the first parameter displayed on

the screen is Pr1: Current Transformer Ratio. Press the DOWN button

to access Pr11: TDH-I Set parameter. To see the parameter value,

press the "SET" button and see that the led of the Pr11 parameter is

blinking.
When the parameter led is blinking, you can change the value of the

parameter by using the DOWN and UP buttons. After changing the

value of the parameter, press the SET button to save and press the

ESC button to return to the previous menu without saving.
When the changed parameter value is saved by pressing the SET

button, the device returns to the previous menu, the parameter value

is displayed on the screen and the parameter led does not blink, it

lights up steadily.

8 8 8 8

- 9 8 5

. .

8 8 8 8

- 9 8 5

. . .

8 8 8 8

3 0

. . .

SET

(2sec.)

8 8 8 8

3 5

. . .

Settings

High Voltage

Adjusting the High Voltage Value:

If the Voltage value stays above

the High Voltage Set value for 5 seconds, the device enters a High

Voltage error, it stops compensation, the alarm relay isenergized (it

deacitivates all steps), the alarm led turns on and the High Voltage led

(Pr12: High Voltage) flashes. When the Voltage value stays below 10V

of the High Voltage set value for 5 seconds, the device disables the

High Voltage error, the alarm relay is deenergized, the alarm and

High Voltage led (Pr12: High Voltage) turns off, the Cosine led turns

on. The device restarts compensation.
After entering the settings menu, the first parameter displayed on

the screen is Pr1: Current Transformer Ratio. Press the DOWN button

to access Pr12: High Voltage parameter. To see the parameter value,

press the "SET" button and see that the led of the Pr12 parameter is

blinking.
When the parameter led is blinking, you can change the value of the

parameter by using the DOWN and UP buttons. After changing the

value of the parameter, press the SET button to save and press the

ESC button to return to the previous menu without saving.
When the changed parameter value is saved by pressing the SET

button, the device returns to the previous menu, the parameter value

is displayed on the screen and the parameter led does not blink, it

lights up steadily.

8 8 8 8

- 9 8 5

. .

8 8 8 8

- 9 8 5

. . .

8 8 8 8

3 0

. . .

SET

(2sec.)

8 8 8 8

3 5

. . .

DOWN

Содержание RGM-12S



























Результаты поиска

Содержание RGM-12S

Отзывы:

Похожие инструкции для RGM-12S

Бренды по названию

Популярные бренды

Tense RGM-12S, Руководство пользователя

Результаты поиска

Содержание RGM-12S

Отзывы:

Похожие инструкции для RGM-12S

Бренды по названию

Популярные бренды