Tenma 72-3555 Скачать руководство пользователя

Страница: 39 / 58

OUTPUTTING FREQUENCY SWEEP WAVEFORMS

•

In Frequency Sweep, the Generator, within the specified sweep time, steps from

start frequency to stop frequency with linear or logarithmic spacing.

•

Internal, external and manual trigger source are available to select. The Generator

can sweep sine, square, ramp and arbitrary waveforms.

•

CH1 and CH2 can be modulated independently with modulation types applied with

the same one or different ones.

Enabling Frequency Sweep

•

Press

Menu→Sweep

to enable the Sweep

function and with the function enabled,

the Generator will output sweep waveform

according to current settings.

Selecting Frequency Sweep Waveforms

•

With Sweep enabled, press

Carrier

to access

sweep waveforms and reveal the interface as

shown right.

Start Frequency and Stop Frequency

•

The start frequency and stop frequency specify

the high and low limits for frequency sweep.

•

The Generator always moves from the start

frequency to stop frequency, and returns to the

start frequency again.

•

To set start frequency or stop frequency,

press the

Return

button to return to Sweep

interface after finishing carrier parameter setup, then use the multipurpose knob

and direction buttons to perform the setting, or press

Params→StartFreq

Stop

Freq

to select, then enter in the desired value with numeric keypad, and press the

corresponding MHz to select the desired unit and finish the setup.

•

Start frequency<Stop frequency: the generarator sweeps up in frequency.

•

Start frequency>Stop frequency: the generarator sweeps down in frequency.

•

Start frequency=Stop frequency: the generarator outputs a fixed frequency.

•

Sweep mode synchronization signal is a signal where the period between start to

middle of sweep time is low, and middle to end of sweep time is high.

•

The default start frequency is 1kHz and the stop frequency default is set at 2kHz.

•

Start frequency and stop frequency ranges depend on functions selected and

could be different. See the following table for details.

Содержание 72-3555



























































Результаты поиска

Содержание 72-3555

Отзывы:

Похожие инструкции для 72-3555

Бренды по названию

Популярные бренды

Tenma 72-3555, Руководство пользователя

Результаты поиска

Содержание 72-3555

Отзывы:

Похожие инструкции для 72-3555

Бренды по названию

Популярные бренды